Using your shaver
Caution – The system outer foil is very thin and can be damaged if handled improperly. Before each use, always check the foll for dam- age. To avoid personal injury, do not use if the foil or other parts of the shaving head is damaged.
(see fig. 2 through 6)
Remove the protective cap and ap- ply shaving lather generously. For the best results, move the shaver in back and forth directions, while keeping the shaver head at a right angle (90°) to your skin so that the two trimmers and outer foil work together at the same time. Slide the
•Underarm (see fig. 3)
Hold your arm up enough to stretch your skin and shave back and forth.
•Legs (see fig. 4)
Be sure to move the shaver from ankle to knee.
•Arms (see fig. 5)
Be sure to move the shaver from outside to inside.
•Bikini (see fig. 6)
You can use the
1.To attach
2.Depress button to release comb when adjusting comb length.
Pivot action selector
(see fig.
Use the pivot action selector to choose the shaving mode:
full range, mid range or lock based on your shaving preference.
Cleaning
(see fig. 7)
For cleanliness and convenience, we recommend that you clean your shaver with water and a liquid hand soap. Regular cleaning will keep your shaver in good condition while pre- venting odors or bacteria from devel- oping, and maintain the cutting per- formance.
With the outer foils in place, apply some hand soap onto the outer foils. Turn the shaver on and turn off after few seconds.
Next, press the outer foil frame re- lease buttons to remove the outer foil frame and rinse the inner blade/outer foils under running water or in a ba- sin.
DO NOT USE BOILING WATER. After the inner blade/outer foils and the shaving head are dry, close the outer foil frame and place the protec- tive cap.
Replacing shaving head Components
It is recommended that you replace the outer foil at least once every year and the inner blade at least once every two years to maintain your shaver’s cutting performance.
Replacing the outer foil
Press the outer foil frame release but- tons to remove the outer foil frame (see fig. 8).
Then, squeeze the front and the back side of the foil frame and lift up one of the two knobs on the outer foil (see fig. 9).
Inserting the new outer foil
Slip the foil into the frame and guide the plastic edges onto the hooks into the frame until it clicks into the shaver.
Replacing the inner blade (see fig. 10)
Squeeze the outer foil release but- tons and lift the outer foil frame up- ward to remove it. Remove the inner blade by grasping it firmly at both ends and pulling straight away from the shaver. To insert the new inner blade, hold the blade at both ends and press downward until it snaps into the shaver.
ATTENTION:
A nickel cadmium battery that is recyclable powers the product you have purchased. At the end of its useful life, under various state and local laws, it is illegal to dispose of this battery into your municipal waste stream. Please call
How to remove the
The battery in this shaver is not in- tended to be replaced by consumers. However, the battery may be re- placed at an authorized service center. The procedure described be- low is intended only for removal of the rechargeable battery for the purpose of proper disposal.
WARNING:
Do not attempt to replace the bat- tery for the purpose of reusing the shaver. This could result in the risk of fire or electric shock.
1.Remove the back rubber panel (a) and the front panel (b) with a flat screwdriver. (see fig. 11)
2.Remove two screws (c). (see fig. 12)
3.Pull the housing (d) out of the end cap. (see fig. 13)
4.Remove two screws (e) and pull the battery frame (f). (see fig. 14)
5.Remove the battery (g) with a flat screwdriver. (see fig. 15)
ATTENTION:
This laws of various states and municipalities restrict disposal of rechargeable batteries (and prod- ucts from which such batteries have not been removed) in ordi- nary household waste. Please comply with your local laws. If you are not certain as to proper dis- posal, please contact your local sanitation department.
8
9
9