Panasonic MC-V5203 Hose Replacement, POWER CORD/ON-OFFSWITCH REPLACEMENT Cont, Installation

Page 6
 POWER CORD/ON-OFF SWITCH REPLACEMENT (Cont.)

 HOSE REPLACEMENT EXPLODED VIEW (BODY, MOTOR HOUSING, AND MOTOR)… C BLOCK

 

 

C-54

 

 

 

C-50

 

 

C-33

 

 

 

 

 

 

C-18

C-48

 

 

 

 

 

 

 

 

 

C-49

 

 

 

 

 

 

 

 

C-37

 

 

 

C-5

 

 

 

 

 

 

 

 

 

C-3

 

 

 

 

 

C-36

 

 

C-4

 

 

 

Tabs

 

 

 

 

 

 

 

C-38

 

 

 

C-17

 

 

C-10

 

 

 

 

 

 

 

 

 

C-46

C-43

C-26

C-2

 

 

 

 

 

C-44

 

 

 

 

C-6

C-45

 

 

C-9

 

 

 

 

 

 

 

 

 

C-1

 

C-8

 

 

 

C-19

 

 

 

 

 

 

 

C-20

 

 

C-52

C-35

 

 

 

 

 

 

 

 

C-42 C-39

 

 

 

 

 

Replacement POWER CORD/ON-OFF SWITCH REPLACEMENT (Cont.)

Installation

1.Insert the new power cord (power cord replacement only) into the dust compartment as far as necessary in order to place a new cord retainer in proper location on power cord. The proper location is approximately one and one eighth inches/thirty millimeters (1 1/8”/30 mm) of new power cord yellow outer jacket extending past the cord retainer and washer. The washer goes between the cord retainer and the dust compartment. Attach wires with wire connectors according to the wiring diagram in the front of this manual. ONLY USE A NEW

CORD RETAINER, DO NOT REUSE A CORD RETAINER.

2.For switch replacement only, insert the new ON/OFF switch with the numbers 1,2,3, facing toward you, into the dust compartment until secured by the retaining tabs. Use a wire tie with the part number listed in the C Block parts list and place it in the location shown in (Fig. 15) taking care not to overtighten it. Tuck the wire connectors back into the dust compartment as shown in the close-up view in (Fig. 15).

3.Ensure that the Insulator Packing is installed correctly, (see Fig. 16).

4.Replace the switch cover, the two (2) switch cover screws, and the dust cover. Care should be taken not to pinch wires and make sure that the switch cover goes on easily and stays flat. If there is resistance to the switch cover lying flat and in place, stop, remove the cover and make sure that no wires are being pinched. DO NOT USE A POWER SCREWDRIVER TO SECURE THE COVER.

NOTE: Any service involving the handle or switch cover area should be followed up with a dielectric or current leakage check of the unit. If you do not have the equipment or are not familiar with the test procedures, take the unit to an authorized servicer.

Manual background HOSE REPLACEMENT

Removal

1.Remove the dust cover and dust bag.

2.Remove the end of the hose from the wand. Remove the hose by removing the two screws which secure it to the dust container.

Replacement

1. Install the new hose by replacing the two screws which secure it to the dust container.

C-7

C-51

C-15 C-13C-16

C-47

C-40 C-31C-41

C-27

2.

Replace the hose onto the wand.

3.

Replace the dust bag and dust cover.

C-14 C-30

C-16

C-53

C-22

C-23

C-34

C-13C-15 C-25

C-28

C-29

C-24

C-21

 

C-32

C-12

C-11

- 6 -

- 15 -

Image 6 Panasonic MC-V5203 service manual Hose Replacement, POWER CORD/ON-OFFSWITCH REPLACEMENT Cont, Installation, Removal
Contents SPECIFICATIONS ServiceManualCommercial Vacuum Cleaner MC-V5203TABLE OF CONTENTS Front CoverSCHEMATIC DIAGRAM WIRING MANAGEMENT DRAWINGEXPLODED VIEW AGITATOR ASSEMBLY... B BLOCK MOTOR FAN REPLACEMENTEXPLODED VIEW NOZZLE HOUSING… A BLOCK InstallationPARTS LIST NOZZLE HOUSING… A BLOCK MOTOR REPLACEMENTCARBON BRUSH REPLACEMENT PARTS LIST AGITATOR ASSEMBLY... B BLOCKReplacement HOSE REPLACEMENTPOWER CORD/ON-OFFSWITCH REPLACEMENT Cont InstallationDUST COMPARTMENT COMPONENT LOCATIONS SWITCH COVER AREA WIRING MANAGEMENTPOWER CORD/ON-OFFSWITCH REPLACEMENT RemovalEXPLODED VIEW MOTOR FAN ASSEMBLY NOZZLE HOUSING AND SHORT HOSE REPLACEMENTPARTS LIST MOTOR FAN ASSEMBLY InstallationWhen to replace brushes BRUSH REPLACEMENTPARTS LIST PACKAGING AGITATOR ASSEMBLYBELT REPLACEMENT LOWER PLATE REMOVAL/INSTALLATIONAGITATOR ASSEMBLY REMOVAL/INSTALLATION Installation