Sentry Industries Sentry 2.0 Display Lights, How to Get IdLE to Display, Repeat Firings

Page 5

Display Lights

Single Center Light: Time

A lower center dot appears during time display. It sepa- rates hours from minutes (i.e. 1 hour, 30 minutes displays as 01.30). During temperature display, the dot disappears.

Power Output Lights

The Sentry turns on the heating elements intermittently through relays. The power output lights in the right side of the display appear when the Sentry sends power to the re- lay(s).

Single Zone Kiln When the Sentry sends power to the relays, all three lights appear.

Two Zone Kiln The top light shows power to the relay for the top section of the kiln. The bottom light shows power to the bottom. Ignore the center light.

Three Zone Kiln The top light indicates power to the top section relay, the middle light to the middle section, and the bottom light to the bottom.

°F °C

Single Right-Hand Light: °C

When temperature is displayed in °C, a light appears in the lower right. In °F it disappears.

How to Get IdLE to Display

The controller displays IdLE when you first apply power to the kiln. Operations begin from IdLE . You can’t fire the kiln until IdLE appears.

If you press STOPduring a firing, AbRT will appear. To get back to IdLE , press ENTER.

If the display shows an error message such as FAIL in- stead of IdLE , see pages 22 - 23.

CPLT (firing completed) appears at the end of a firing. To make IdLE appear, press any key.

Firing Completion Message

When the firing has completed, four messages will cycle one after the other:

1CPLT (complete)

2Firing time in hours and minutes (amount shown does not include Cone-Fire slow cooling time)

3The temperature the kiln fired to in Cone-Fire, or the temperature of the last segment in Ramp-Hold

4The current kiln temperature

Note: If the alarm (see page 6) sounded, and then the kiln fired to completion, you will see ALAR in- stead of CPLT . Press ENTER. CPLT will appear.

Repeat Firings

To repeat the last firing, press ENTER from IdLE . The kiln will begin firing. This works in both Cone-Fire and Ramp-Hold. But first, make sure you are repeating the cor- rect firing by using “Program Review” (see page 6). For re- peat firings that you don’t want to inadvertently change, see “Program Lock,” page 20.

Thermocouple Inspection

The small rod protruding into the firing chamber is the temperature sensor, or thermocouple.

CAUTION: Bumping the thermocouple can push it out of the firing chamber. This could cause an overfire! The controller does not contain an alarm to detect this type of failure.

Thermocouples come in different widths. The wider the thermocouple, the farther it should extend into the firing chamber. A ¼” diameter thermocouple should extend into the firing chamber about 1”. A 1/8” thermocouple should ex- tend into the chamber ½” - 5/8”.

Keep shelves, posts and ware 1” - 1 ½” away from the thermocouple. Keep an extra thermocouple on hand, espe- cially if you fire hotter than 2000°F/1093°C.

If you are using a portable, separate controller, you will need to install the thermocouple onto the kiln. See the sepa- rate TnF 2 installation instructions.

The “LId” Display

Reasons LId appears in the display:

The kiln is equipped with the optional safety switch. (The switch turns off power to the elements when the lid or door is open.) LId appears in the display while the lid is open during firing.

On the back of the Sentry circuit board, at the top right

side, is a small two-pin terminal. If the connector on that terminal is missing, LId will appear in the display dur- ing firing. The elements will not turn on. (If the two-pin connector is missing, you can buy another from a com- puter supply store.)

The safety lid switch is defective or the safety switch wire is broken.

5

Image 5
Contents Multiple Zone Options Standard OptionsIntroduction Contents Room Temperature and Humidity SafetyThunder Storms and Power Surges Basic PointersDisplay Lights How to Get IdLE to DisplayFiring Completion Message Repeat FiringsKeys Enter/Start Cone Numbers Skip SegmentOptions Key Stop/Back KeyCone-Fire How to Position Cones on the ShelfPyrometric Witness Cones Firing SchedulesPre-Heat Prht Cone-Fire FeaturesSpeed SPd Mirror Test Cone-Fire ProgrammingHold HOLd Slow Cooling Cool When the Kiln Shuts Off Too SoonFor Kilns with AOP Outlet Wrong Thermocouple TypeDefinition of a Segment Ramp-HoldUser Programs User Ramp-Hold ProgrammingRate Firing a Stored User ProgramAOP Fan Segments for Controlled CoolingStarting a Firing in a Hot Kiln Glass Fusing Firing ScheduleGlass Slumping Firing Schedule Ceramic FiringsMultiple Zone Kilns Cone-Fire Options OptionsCone-Fire Speed Spd Cone Offset OfstThermocouple Offset Tcos General OptionsFan FAN Thermocouple Type TC Selecting F or C CHGMaximum Temperature Sfty Temperature Deviation TedeElectronics Temperature Elec AOP Outlet AOPMultiple Zone Options Terminating Error Messages Error MessagesNon-Interrupting Error Messages Plog Error Codes How the Sentry Handles Power FailuresTCdE / Uneven Multiple Zone Temperatures TCR / Thermocouple Leads ReversedAppendix a Display Messages Diagnostic Test Failure Power FailureReset SafetyCone Rate 1 Temp Rate 2 Temp Low Fire Cones FSegment Low Fire Cones C Appendix B Preset Standard Cone-Fire Schedules CUpgrading the DTC 100, 600, 800 & 1000 to the Sentry Appendix C Upgrading InstructionsPage 022 Cone Self-Supporting Cones Pre-Fire Number Color010 05 1/2Kiln is now firing. Use Program Review by pressing Appendix ESentry Ramp-Hold Shorthand Instructions Kiln is now firing to the cone you selected Appendix FSentry Cone-Fire Shorthand Programming

Sentry 2.0 specifications

Sentry Industries has recently unveiled the Sentry 2.0, an innovative enhancement to their line of security solutions. This state-of-the-art platform is designed to address modern security challenges with a blend of advanced technology and user-centric features.

One of the standout features of Sentry 2.0 is its integrated artificial intelligence capabilities. The system employs machine learning algorithms to analyze behavior patterns, allowing for real-time threat detection and response. This proactive approach means that potential security breaches can be identified and mitigated before they escalate, significantly reducing risk for businesses and individuals alike.

In addition to its AI-driven technology, Sentry 2.0 boasts an intuitive user interface that simplifies the management of security systems. This user-friendly design enables users, regardless of their technical know-how, to configure and monitor security settings effortlessly. The dashboard provides a comprehensive overview of the security landscape, displaying real-time data, alerts, and system status updates in a clear and accessible manner.

Another notable characteristic of Sentry 2.0 is its robust integration capabilities. The platform can seamlessly connect with various security devices, including cameras, motion sensors, and access control systems, creating a unified security ecosystem. This interoperability ensures that users can easily expand or customize their security solutions as their needs change over time.

Sentry 2.0 also prioritizes data privacy and protection. With end-to-end encryption and secure cloud storage, users can trust that their sensitive information is safeguarded against unauthorized access. The platform complies with industry standards and regulations, offering peace of mind in an increasingly digital landscape.

Moreover, Sentry 2.0 includes advanced reporting features, enabling users to generate insights from their security data. These analytics can help organizations understand trends, optimize response strategies, and ultimately enhance their overall security posture. The ability to generate customized reports empowers businesses to make informed decisions based on detailed analyses of their security systems.

In summary, Sentry Industries has positioned the Sentry 2.0 as a cutting-edge solution in the realm of security technology. With its AI capabilities, user-friendly interface, integration versatility, data protection measures, and advanced reporting, Sentry 2.0 addresses the diverse needs of today's security landscape, setting a new standard for security solutions.