Sanyo 550 Cabinet and Program Start UP, Cabinet and Program Shut Down, To Start the Cabinet

Page 19

5.2. CABINET AND PROGRAM START UP

Ensure that:

a)The interior of the cabinet is clean and dry.

b)You know how to SHUT DOWN the cabinet (see section 5.4).

c)Distilled water level is adequate

d)Clean wicks are fitted to the wet bulb sensor(s).

TO START THE CABINET:

a)Switch the MAINS red/yellow isolator fitted to the front control panel to ON. The MAINS pushbutton on the front control panel will become illuminated green.

b)Power is now available to the Format 550 controller and settings for required test or cycle are entered - see Part 2 of this manual for the Format 550 instructions..

c)Start manual control or the desired program.

d)Press and hold the RESET pushbutton until the cabinet starts. The reset orange indi- cator light will extinguish when the cabinet starts.

e)The Format 550 will now control the cabinet.

5.3.CABINET AND PROGRAM SHUT DOWN

TO SHUT DOWN THE CABINET - NORMAL SEQUENCE:

a)To terminate steady state or two setpoint cycling control - see Format 550 instruc- tions.

b)When control by Format 550 has been completed or terminated switch the cabinet's red/yellow mains isolator to OFF. The cabinet conditions will now drift slowly to ambient.

EMERGENCY SHUT DOWN:

a) Switch the MAINS red/yellow isolator fitted to the front control panel to OFF.

18

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Environmental Chamber Sanyo GallenkampCustomer De Ronde Programming system Contents Part ONE the Cabinet Commissioning U.K. Customers only Health & Safety at WorkSanyo Gallenkamp service & maintenance facilities IntroductionCabinet Data Specification PhysicalFalse roof Exterior/finishInsulation ShelfOptional Facilities Specification PerformanceCF1 Digital Channel Cooling Auxiliary Format 550 Digital ChannelsDigital Channel Cooling Main System ChannelUser Programmable Channel Digital Channel 8 Voltage Free Terminal VFTPrinciple and Airflow DESCRIPTI0NRefrigeration unit control Temperature ControlHeating CoolingRelative Humidity Control Vapour phase generationRelative Humidity RH Relative Humidity DeterminationRelative Humidity Decrease Cabinets not requiring on-site commissioning InstallationAccessories & Spares PositioningInstrument compartment Drain Ambient TemperaturePower Supply Mains Interrupt BridgeEither Distilled Water SupplyWetwicks Test Load ProtectionVent 13. RS232 ConnectorSafety Thermostat Cable PortMains INDICATORS/PUSHBUTTONSReset Amber pushbutton Control Panel InstrumentationTo Shut Down the Cabinet Normal Sequence Cabinet and Program Start UPCabinet and Program Shut Down To Start the CabinetMonth Maintenance and CareMaintenance Schedule Weekly or between testsInspection and replacement of the wet wicks Maintenance MethodsInterior and exterior cleaning Cleaning of cabinet drainsDistilled water filter Check safety thermostatClean the refrigeration condenser LubricationAppendix 1 Part Numbers Operation InstallationMaintenance Appendix 2 REC/W Water SystemSystem draining Deioniser replacementPart 2 Format 550 Instructions ContentsFormat digital channels Introduction to FormatHow to use these instructions Menu system Getting startedUsing the data entry windows Using the on-line helpFunction keys Types of data entry field Status barPage General Operating Sequence Steady State Mode Condition settingCondition monitoring Resetting steady state setpointsEnding manual control Main Menu General Operating Sequence Entering a NEW ProgramGeneral Operating Sequence Running a Program Condition C %RH Status LoggingWriting a Program How to use Format programming sheetsEntering the data into the programmer Selecting digital channels when you know bestLoading and saving programs Log Running a programHolding a program Program Monitor WindowProgram deletion Program completionView program graph Starting Data Logging Introduction to Data LoggingLog Displaying Results Stopping Data LoggingLoading into Spreadsheets Setting Alarms Introduction to AlarmsPage Host PC System Requirements C0MPUTER InterfacingIntroduction Computer InteractiveSetting UP OFF-LINE Chamber Intelligence InstallationInstalling the Security KEY Configuring the Host SoftwareMain Menu Network Monitoring ModeSteady State Control Logging ProgramPrintouts Program Physical Layer Definition Computer interactive interfacing main protocolCommunications Frame Definition Packet Count HeaderSerial Number Length Data Block Compatibility with RS485 Multi-Controller ConfigurationData Block Length Serial NumberFunctional Layer Definition Controller Configuration RequestController Configuration Packet Flow SummaryStatus Request 129Page Open File for Reading Read Data Close FileWrite Block to File Open File for WritingSET Controller to Local Access Mode SET Controller to Remote Access ModeSET/CHANGE Steady State Condition ENABLE/DISABLE Manual Hold ENABLE/DISABLE Guaranteed SoakDigital Channel Description Computer RS232 Format 550 socket Pin D type Cable connectionsCDR Support software Control Loops Appendix 1 Technical SpecificationOperating temperature Operator interface data entryData Logging AlarmsProgram Run Options Monitoring displaysTemp Hum LS Rep Digital Channels Ddhhmmss C Appendix 2 Program Looping and Nested LoopsLoop Instructions ExampleEvent statement time = event actual time total looping time Calculation for Succeeding EventsEffects on the Running Timebase Display Nested LoopsSeconds Example of Nested Loops Format Programming Sheet Appendix 3 Format 550 Programming SheetsLEU ORE Contact Information

550 specifications

The Sanyo 550 is a remarkable piece of technology, encapsulating innovative features and advanced characteristics that cater to a variety of users. This device, designed with meticulous attention to detail, is particularly renowned for its versatility and user-friendly interface.

One of the standout features of the Sanyo 550 is its impressive display technology. The high-resolution screen offers vibrant colors and sharp images, making it ideal for both professional presentations and personal entertainment. Whether you're watching videos or reviewing documents, the clarity provided by the Sanyo 550's display enhances the overall user experience.

In terms of connectivity, the Sanyo 550 excels with multiple options available, including USB ports, Bluetooth, and Wi-Fi capabilities. These features allow users to seamlessly connect various devices, transfer files effortlessly, and access the internet without hassle. This level of connectivity ensures that the Sanyo 550 can function as a central hub for all your multimedia needs, whether for work or leisure.

The Sanyo 550 also incorporates advanced battery technology. With its long-lasting power supply, users can enjoy extended usage without frequent recharging. This is particularly beneficial for individuals who are constantly on the go, as it allows for uninterrupted productivity and entertainment.

Moreover, the Sanyo 550 is designed with portability in mind. Its lightweight and compact design make it easy to carry, fitting comfortably in a bag or briefcase. This feature is particularly appealing for professionals who travel frequently or students who need a reliable device for classes and study sessions.

The device is also equipped with powerful processing capabilities, enabling smooth multitasking and efficient performance. Whether running demanding applications or performing routine tasks, the Sanyo 550 maintains high performance levels, ensuring a satisfying user experience.

Lastly, the Sanyo 550 places emphasis on user satisfaction through its intuitive operating system. The interface is designed to be straightforward and accessible, allowing users of all tech-savvy levels to navigate with ease. Overall, the Sanyo 550 represents a blend of cutting-edge technology, portability, and user-centered design, making it a compelling choice for anyone in the market for a reliable and feature-rich device.
Top Page Image Contents