Sanyo 550 Control Panel Instrumentation, Indicators/Pushbuttons, Mains, Reset Amber pushbutton

Page 18

5.0PERATI0N

WARNING

This cabinet is capable of temperatures well outside ambient. If the door is opened during such conditions there could be a temperature HAZARD from cabinet air or contents.

5.1. CONTROL PANEL INSTRUMENTATION

Full details of the Format 550 programmer/controller fitted to the cabinet are given in Part 2.

If there are any further controls not mentioned here, refer to 2.3 - Additional facilities fitted.

5.1.1INDICATORS/PUSHBUTTONS

Mains

Green indicator lamp

The mains indicator is illuminated green when mains power is supplied to the cabinet and the mains power switch (red/yellow rotary switch) is switched on.

Reset

Amber pushbutton

Internal lamp glows whenever the cabinet is powered but not reset. Press to reset and start the cabinet. The reset button is not illuminated when the cabinet is running.

5.1.2RECORDER

If a recorder is fitted it should be set up and operated in accordance with the manufacturer's instructions, packed either with this manual or inside the instrument itself.

17

Page 17 Page 19
Image 18
Page 17 Page 19
Contents
Sanyo Gallenkamp Environmental ChamberCustomer De Ronde Programming system Contents Part ONE the Cabinet Introduction Health & Safety at WorkSanyo Gallenkamp service & maintenance facilities Commissioning U.K. Customers onlySpecification Physical Cabinet DataShelf Exterior/finishInsulation False roofSpecification Performance Optional FacilitiesCF1 System Channel Format 550 Digital ChannelsDigital Channel Cooling Main Digital Channel Cooling AuxiliaryDigital Channel 8 Voltage Free Terminal VFT User Programmable ChannelDESCRIPTI0N Principle and AirflowCooling Temperature ControlHeating Refrigeration unit controlRelative Humidity Determination Vapour phase generationRelative Humidity RH Relative Humidity ControlRelative Humidity Decrease Positioning InstallationAccessories & Spares Cabinets not requiring on-site commissioning Instrument compartment Mains Interrupt Bridge Ambient TemperaturePower Supply DrainTest Load Protection Distilled Water SupplyWetwicks EitherCable Port 13. RS232 ConnectorSafety Thermostat VentControl Panel Instrumentation INDICATORS/PUSHBUTTONSReset Amber pushbutton MainsTo Start the Cabinet Cabinet and Program Start UPCabinet and Program Shut Down To Shut Down the Cabinet Normal SequenceWeekly or between tests Maintenance and CareMaintenance Schedule MonthCleaning of cabinet drains Maintenance MethodsInterior and exterior cleaning Inspection and replacement of the wet wicksLubrication Check safety thermostatClean the refrigeration condenser Distilled water filterAppendix 1 Part Numbers Appendix 2 REC/W Water System InstallationMaintenance OperationDeioniser replacement System drainingContents Part 2 Format 550 InstructionsIntroduction to Format Format digital channelsHow to use these instructions Getting started Menu systemUsing the on-line help Using the data entry windowsFunction keys Status bar Types of data entry fieldPage Condition setting General Operating Sequence Steady State ModeResetting steady state setpoints Condition monitoringEnding manual control Condition C %RH Status Logging General Operating Sequence Entering a NEW ProgramGeneral Operating Sequence Running a Program Main MenuHow to use Format programming sheets Writing a ProgramSelecting digital channels when you know best Entering the data into the programmerLoading and saving programs Running a program LogProgram Monitor Window Holding a programProgram completion Program deletionView program graph Introduction to Data Logging Starting Data LoggingLog Stopping Data Logging Displaying ResultsLoading into Spreadsheets Introduction to Alarms Setting AlarmsPage Computer Interactive C0MPUTER InterfacingIntroduction Host PC System RequirementsConfiguring the Host Software InstallationInstalling the Security KEY Setting UP OFF-LINE Chamber IntelligenceNetwork Monitoring Mode Main MenuSteady State Control Program LoggingPrintouts Program Computer interactive interfacing main protocol Physical Layer DefinitionCommunications Frame Definition Header Packet CountSerial Number Length Serial Number Compatibility with RS485 Multi-Controller ConfigurationData Block Length Data BlockPacket Flow Summary Controller Configuration RequestController Configuration Functional Layer Definition129 Status RequestPage Open File for Reading Close File Read DataOpen File for Writing Write Block to FileSET Controller to Remote Access Mode SET Controller to Local Access ModeSET/CHANGE Steady State Condition ENABLE/DISABLE Guaranteed Soak ENABLE/DISABLE Manual HoldDigital Channel Description Cable connections Computer RS232 Format 550 socket Pin D typeCDR Support software Operator interface data entry Appendix 1 Technical SpecificationOperating temperature Control LoopsMonitoring displays AlarmsProgram Run Options Data LoggingExample Appendix 2 Program Looping and Nested LoopsLoop Instructions Temp Hum LS Rep Digital Channels Ddhhmmss CCalculation for Succeeding Events Event statement time = event actual time total looping timeNested Loops Effects on the Running Timebase DisplaySeconds Example of Nested Loops Appendix 3 Format 550 Programming Sheets Format Programming SheetContact Information LEU ORE
Top Page Image Contents