Sanyo 550 instruction manual Distilled Water Supply, Wetwicks, Test Load Protection, Either

Page 16

Two small black plastic pipes are also fitted to the right hand side or rear of the cabinet. These are overflows from the wick reservoir and vpg humidification system self levelling header tanks. If a float valve develops a fault, the respective overflow will operate preventing flooding of the instrument compartment

4.7. DISTILLED WATER SUPPLY

EITHER

Connect the distilled water supply to inlet connector situated on the right side or at the rear of the cabinet. Maximum allowable head is 1500mm (5ft) above the inlet.

It is safe for a container to stand on top of the cabinet, but ideally any reservoir should have its own support to one side of the cabinet.

OR

If the cabinet is supplied with a water re-circulating system, fill the reservoir as instructed and connect the water connections to the cabinet water inlet and drain as shown..

4.8. WETWICK(S)

(See Section 6.2.4 wet wicks)

Wet bulb sensor(s) must be fitted with wet wick(s).

Anchor the wick in the water reservoir and then push it over the sensor. The wick should be taut but not stretched. The sensor must be completely covered. If any part of the sensor is uncovered or protrudes through the weave then accuracy will be impaired.

Keep wick material clean. Contamination affects absorbency and hence RH control.

4.9. TEST LOAD PROTECTION

A safety thermostat should be fitted to all equipment being powered inside the cabinet. The thermostat should switch off equipment power if the air temperature in the cabinet rises above safety level.

The thermostat will protect both the equipment and the cabinet against damage in the event of failure or shut down of the cabinet's temperature control system. Equipment dissipating only a few hundred watts inside the well insulated cabinet, with no cooling, will heat sufficiently to cause severe damage.

Advice on suitable thermostats is available from our Technical Department.

SANYO GALLENKAMP will not be held responsible for any damage to either equipment or cabinet, during or after the cabinet guarantee period, caused by heat dissipation from unprotected equipment.

If the cabinet is fitted with a glass inner door and the load being tested in the cabinet is liable to dissipate excessive heat, the glass inner door must be protected from absorbing this heat by radiation effect. Failure to protect the inner door could result in the glass cracking.

15

Image 16
Contents Environmental Chamber Sanyo GallenkampCustomer De Ronde Programming system Contents Part ONE the Cabinet Health & Safety at Work Sanyo Gallenkamp service & maintenance facilitiesIntroduction Commissioning U.K. Customers onlySpecification Physical Cabinet DataExterior/finish InsulationShelf False roofOptional Facilities Specification PerformanceCF1 Format 550 Digital Channels Digital Channel Cooling MainSystem Channel Digital Channel Cooling AuxiliaryDigital Channel 8 Voltage Free Terminal VFT User Programmable ChannelDESCRIPTI0N Principle and AirflowTemperature Control HeatingCooling Refrigeration unit controlVapour phase generation Relative Humidity RHRelative Humidity Determination Relative Humidity ControlRelative Humidity Decrease Installation Accessories & SparesPositioning Cabinets not requiring on-site commissioningInstrument compartment Ambient Temperature Power SupplyMains Interrupt Bridge DrainDistilled Water Supply WetwicksTest Load Protection Either13. RS232 Connector Safety ThermostatCable Port VentINDICATORS/PUSHBUTTONS Reset Amber pushbuttonControl Panel Instrumentation MainsCabinet and Program Start UP Cabinet and Program Shut DownTo Start the Cabinet To Shut Down the Cabinet Normal SequenceMaintenance and Care Maintenance ScheduleWeekly or between tests MonthMaintenance Methods Interior and exterior cleaningCleaning of cabinet drains Inspection and replacement of the wet wicksCheck safety thermostat Clean the refrigeration condenserLubrication Distilled water filterAppendix 1 Part Numbers Installation MaintenanceAppendix 2 REC/W Water System OperationDeioniser replacement System drainingContents Part 2 Format 550 InstructionsIntroduction to Format Format digital channelsHow to use these instructions Getting started Menu systemUsing the data entry windows Using the on-line helpFunction keys Status bar Types of data entry fieldPage Condition setting General Operating Sequence Steady State ModeResetting steady state setpoints Condition monitoringEnding manual control General Operating Sequence Entering a NEW Program General Operating Sequence Running a ProgramCondition C %RH Status Logging Main MenuHow to use Format programming sheets Writing a ProgramSelecting digital channels when you know best Entering the data into the programmerLoading and saving programs Running a program LogProgram Monitor Window Holding a programProgram deletion Program completionView program graph Starting Data Logging Introduction to Data LoggingLog Displaying Results Stopping Data LoggingLoading into Spreadsheets Introduction to Alarms Setting AlarmsPage C0MPUTER Interfacing IntroductionComputer Interactive Host PC System RequirementsInstallation Installing the Security KEYConfiguring the Host Software Setting UP OFF-LINE Chamber IntelligenceMain Menu Network Monitoring ModeSteady State Control Logging ProgramPrintouts Program Physical Layer Definition Computer interactive interfacing main protocolCommunications Frame Definition Packet Count HeaderSerial Number Length Compatibility with RS485 Multi-Controller Configuration Data Block LengthSerial Number Data BlockController Configuration Request Controller ConfigurationPacket Flow Summary Functional Layer Definition129 Status RequestPage Open File for Reading Close File Read DataOpen File for Writing Write Block to FileSET Controller to Local Access Mode SET Controller to Remote Access ModeSET/CHANGE Steady State Condition ENABLE/DISABLE Manual Hold ENABLE/DISABLE Guaranteed SoakDigital Channel Description Computer RS232 Format 550 socket Pin D type Cable connectionsCDR Support software Appendix 1 Technical Specification Operating temperatureOperator interface data entry Control LoopsAlarms Program Run OptionsMonitoring displays Data LoggingAppendix 2 Program Looping and Nested Loops Loop InstructionsExample Temp Hum LS Rep Digital Channels Ddhhmmss CCalculation for Succeeding Events Event statement time = event actual time total looping timeNested Loops Effects on the Running Timebase DisplaySeconds Example of Nested Loops Appendix 3 Format 550 Programming Sheets Format Programming SheetContact Information LEU ORE

550 specifications

The Sanyo 550 is a remarkable piece of technology, encapsulating innovative features and advanced characteristics that cater to a variety of users. This device, designed with meticulous attention to detail, is particularly renowned for its versatility and user-friendly interface.

One of the standout features of the Sanyo 550 is its impressive display technology. The high-resolution screen offers vibrant colors and sharp images, making it ideal for both professional presentations and personal entertainment. Whether you're watching videos or reviewing documents, the clarity provided by the Sanyo 550's display enhances the overall user experience.

In terms of connectivity, the Sanyo 550 excels with multiple options available, including USB ports, Bluetooth, and Wi-Fi capabilities. These features allow users to seamlessly connect various devices, transfer files effortlessly, and access the internet without hassle. This level of connectivity ensures that the Sanyo 550 can function as a central hub for all your multimedia needs, whether for work or leisure.

The Sanyo 550 also incorporates advanced battery technology. With its long-lasting power supply, users can enjoy extended usage without frequent recharging. This is particularly beneficial for individuals who are constantly on the go, as it allows for uninterrupted productivity and entertainment.

Moreover, the Sanyo 550 is designed with portability in mind. Its lightweight and compact design make it easy to carry, fitting comfortably in a bag or briefcase. This feature is particularly appealing for professionals who travel frequently or students who need a reliable device for classes and study sessions.

The device is also equipped with powerful processing capabilities, enabling smooth multitasking and efficient performance. Whether running demanding applications or performing routine tasks, the Sanyo 550 maintains high performance levels, ensuring a satisfying user experience.

Lastly, the Sanyo 550 places emphasis on user satisfaction through its intuitive operating system. The interface is designed to be straightforward and accessible, allowing users of all tech-savvy levels to navigate with ease. Overall, the Sanyo 550 represents a blend of cutting-edge technology, portability, and user-centered design, making it a compelling choice for anyone in the market for a reliable and feature-rich device.