|
| Vertical track Top of track | |
1st hole set | 2nd hole set | 3rd hole set |
|
Lower hole of |
|
|
|
hole/ slot pattern | 1/4”- 20 |
|
|
| Flange hex nut |
| Jamb bracket |
|
|
| |
|
| 1/4”- 20 x | in place |
|
|
| |
|
| 9/16” |
|
| F.A. jamb | Track bolt |
|
|
|
| |
| bracket |
|
|
6 | Lift Handles | |
Tools: Tape Measure, Pencil, Power Drill, 1/16” Drill Bit | ||
|
NOTE: Refer to door section identification, located in the
Starting with the lock section, measure the width of the center stile which will receive the lift handle(s). Divide that measurement in half and mark a vertical line onto the center of the stile.
NOTE: If you are installing two lift handles on the center stile, you will need to measure from the edge of the center stile to the center line mark. Divide that measurement in half and draw a second and third vertical line parallel to the previously made center line mark.
Now, measure the height of the panel. Divide that measurement in half and mark a horizontal line, intersecting the vertical line(s) previously marked. Measure up 3 7/8” from the intersect- ing line(s) and mark another horizontal line.
Use the point(s) where the top horizontal line intersects the vertical line(s) to locate the top hole of the lift handle(s). Using the lift handle as a template, mark this location onto the center stile. Keeping the lift handle aligned with the vertical line, mark the lower lift handle hole onto the center stile. Drill 1/16” pilot holes at the marked hole locations. Fasten both lift handles to the center stile using #10 X 5/8” pan head self tapping screws.
If the door came with two sets of lift handles repeat the same process for the other lift handles.
Center stile |
| Center stile |
|
|
|
|
| Vertical | |
|
|
|
| line |
| Vertical |
| ||
|
|
|
| |
|
| line |
|
|
| Horizontal |
| Horizontal |
|
Center line | line | Center line | line |
|
|
|
| ||
Lock section |
| Lock section |
|
|
|
|
| (4) #10 X 5/8” Pan | |
| (2) #10 X 5/8” Pan | head self tapping | ||
| head self tapping | screws | ||
|
| screws |
|
|
| Lift |
| Lift |
|
| handle |
| handle | Center |
|
|
|
| |
Center stile |
| Lift |
| stile |
|
| handle |
|
|
Typical placement of lift |
|
| |
handles referenced on |
|
| |
single wide doors |
| Lock | |
|
|
| |
| Lift handles |
| section |
|
|
| |
| Pull handle |
|
|
| Bottom section |
| 20” Minimum to |
|
|
| 30” Maximum |
Typical placement of lift handles referenced on double wide doors |
| ||
Lift handles |
|
| |
| Bottom |
| Lock |
| section |
| section |
| Pull handle | 20” Minimum to 30” Maximum | Pull handle |
|
| ||
7 | Pull Handles |
| |
Tools: Tape Measure, Pencil, Power Drill, 1/16” Drill Bit | |||
|
|
|
Locate and mark the horizontal and vertical center on the bottom rail of the bottom section, on single car doors.
Center the pull handle using the vertical and horizontal lines as referenced on the bottom section rail. Using the pull handle as a template, mark the two hole locations in the pull handle onto the horizontal line of the bottom section rail. Drill 1/16” pilot holes at the marked hole locations. Fasten pull handle(s) using (2) #10 X 5/8” pan head self tapping screws.
If your door came with two pull handles, locate them directly below the lift handles and repeat the installation process.
Center stile |
|
|
Bottom section |
| (2) #10 X 5/8” Pan |
| head self tapping | |
| Pull handle | |
Bottom rail | screws | |
|
|
Typical placement of pull |
|
|
handle referenced on |
|
|
single wide doors |
| Lock |
|
| |
Lift handles |
| section |
|
| |
Pull handle |
|
|
Bottom section |
| 20” Minimum to |
|
| 30” Maximum |
Typical placement of pull handles referenced on double wide |
| |
Lift handles |
|
|
Bottom |
| Lock |
section |
| section |
Pull handle | 20” Minimum to 30” Maximum | Pull handle |
|
8 | Cable Drum Assemblies and Track Rollers | |
Tools: None | ||
|
NOTE: Refer to door section identification, located in the
NOTE: The bottom section can be identified by the smallest graduated edge hinge of the factory installed graduated edge hinges, see Parts Breakdown on page 2.
7
Please Do Not Return This Product To The Store. Contact your local
refer to your local yellow pages business listings or go to the Find a Dealer section online at