Barco R9000896 Connections, AC Power mains Cord Connection, Power Check, Switching On/Off

Page 10

Connections

3 CONNECTIONS

AC Power (mains) Cord Connection

Use the supplied power cord to connect your projector to the wall outlet. Plug the female power connector into the male connector at the backside of the projector.

V NOM

120/230 Volt

 

 

 

I MAX

7/5Amp

 

 

 

FREQ

50/60Hz

 

 

 

 

IN RS232

OUT RS232

 

 

 

 

 

IR

REMOTE

 

RS232 IN

RS232 OUT

IR

REMOTE

 

 

 

 

685

Power Check

Power voltage indication on sticker on the back side of the projector.

The power voltage is indicated by the art. no.

Warning !

Check if the indicated power voltage corresponds to that of the wall outlet.

Art. No. R9000893 must be connected to a 230 VAC power source.

Art. No. R9000896 must be connected to a 120 VAC power source.

If the wall outlet voltage is different, call a qualified technician for power adaptation of the projector.

Switching On/Off

The projector is switched ON and OFF using the power (mains) switch ON/OFF.

Pressed : ON

Not pressed : OFF

The projector can start now in the 'operational mode' (image dis- played) or in the 'stand by mode', depending on the position of the 'power up' dip switch on the controller unit. This DIP switch must be set during installation by a qualified technician. If you want to change this start up mode, call a qualified technician.

Stand by indication lamp :

no light up : projector switched off

green color : projector in Operational mode

red color : projector is in Standby mode.

T 1

PROJECTOR MODE

EO)

 

GREEN : operational

RED : stand-by

 

PORT 2

ON

(S-VIDEO)

OFF ON

hm

 

 

 

75 ohm

352

5975847 BARCOGRAPHICS 1208S 220197

 

3-1

 

Image 10
Contents Graphics 1208s R9000893 R9000896 Barco Projection Systems Date Art. No 220197 R5975847Barco nv/Projection Systems Noordlaan Kuurne BelgiumTable of Contents Service mode OptionsSafety Instructions On safetyOn servicing On installationOn cleaning On repackingLocation and Function of Controls Stand-by RCU control panel terminologySharpness Switching On/Off AC Power mains Cord ConnectionPower Check ConnectionsComp. Video Video1/Comp. Video Signal Input Connection to the ProjectorPort No Projector input Press Digit Button Start up with full white imageVideo input selection Connecting a Composite Video source to portConnecting a S-Video or Video source to port Input selectionAnalog Input Selection Connecting a RGB Analog source to portConnecting a RGB Analog source to port 4/5 RGB input selectionWith Tri-level sync on green. The projector detects Connecting a Component Video source to port 4/5RGB analog input terminals with Tri level sync input or To select the component video inputConnecting a VS05 switcher to Barcographics 1208s Connecting a Rcvds 05 switcher to the Barcographics 1208sConnecting an IR Remote Receiver to the Barcographics 1208s Battery installation in the RCU ControllingHow to control the projector How to use your RCUHardware set up of the projector address Using your RCUHow to program an address into the RCU? How to display a projector address?Input selection Port No Projector input Press Digit Button Analog Picture Controls Controlling chained projectorsStart UP of the Adjustment Mode Adjustment Mode0000 WrongStarting-Up the Random Access Adjustment mode Overview Random Access Adjustment modeFrom next Internal Cross Hatch Pattern Selecting Setup PatternInternal # Pattern Picture Tuning Random access adjustment mode selection menuColor Balance Clamp Tuning Sync Fast/Slow AdjustmentPeaking Color Select Port 2 Video or S-VideoLine Doubler option Color SelectFocusing Geometry Geometry AdjustmentsHorizontal Phase Adjustment GeometryCrt faceplate border Raster Shift AdjustmentProjected raster Raster ShiftLEFT-RIGHT E-W Left-Right east-west AdjustmentsLEFT-RIGHT Seagull Correction Seagull correctionLeft Side Correction Left Side CorrectionTOP-BOTTOM N-S Top-Bottom north-south AdjustmentsTOP-BOTTOM TOP-BOTTOM N-SHorizontal Size Adjustment Exit will return to GeometryVertical Linearity Adjustment Vertical Size AdjustmentBlanking Adjustments Top blanking Right blanking Bottom blankingConvergence Convergence AdjustmentCoarse Convergence Adjustment Coarse ConvergenceFine Convergence Adjustment Vertical CornersOverview flowchart Service mode Starting up the Service modeService Mode Copy a block Copy ModeIdentification IdentificationDeleting block by block Delete ModeDeletion of blocks Deletion of all blocksRun time Change passwordChange Language Barcographics 1208SConvergence Mid Set to midpositionUndo Midposition Undo Convergence MidpositionDynamic Astigmatism Dynamic Astigmatism spot shape adjustmentDynamic Astigmatism Gamma corrections G2 AdjustCRT run in cycle Projector Warm UP CRT Drive ModeProjector Warm Up Projector Warm UPFh= 15.6 kHz Fv= 050 Hz MESSAGES, Warnings and Failure Codes003 Input not available Iris commu Nication Error I2C error Addr FH3RWI commu Nication Error Invalid RWI soft VersionOptions Orbiting Kit Magik InterfaceCeiling Mount kit CM100 Line Doubler KitOrbiting option Orbiting Mode Toggle SwitchesOrbiting Master/Slave ToggleOrbiting Speed Toggle only in Master Orbiting Adjustment procedure Stand-Alone projectorOrbiting Alignment Adjustment procedure multiple projector installations Adjustment Blocks memory blocks Adjustment Blocks and SourceSource numbers 90 Insert Card

R9000896, R9000893 specifications

Barco, a global leader in visualization and collaboration technologies, has introduced several high-performance projectors designed for diverse applications in various sectors, particularly in professional and commercial environments. Among their innovative product lineup, the Barco R9000893 and R9000896 projectors stand out for their impressive features and technological advancements.

The Barco R9000893 is a flagship model that offers exceptional image quality, making it ideal for high-demand applications such as large venue presentations, corporate events, and immersive installations. One of the key characteristics of this projector is its high brightness capability, which enables it to deliver sharp images even in well-lit environments. With a luminosity of up to 40,000 lumens, the R9000893 ensures that every detail of the presentation is visible, enhancing audience engagement.

Equipped with advanced DLP technology, the R9000893 also provides outstanding color accuracy and contrast. This ensures that colors are vibrant and true-to-life, which is particularly important for applications like art installations or product showcases where visual fidelity is paramount. Additionally, the projector boasts a native 4K resolution, allowing for the display of ultra-high-definition content without any compromise on quality.

Similarly, the Barco R9000896, while slightly more compact in design, does not compromise on performance. This model features a similar high brightness capability and offers versatile connectivity options, making it suitable for a wide range of applications, from rental and staging to fixed installations. The R9000896 also includes built-in image processing technologies that enhance image quality and provide seamless scaling of various content formats.

Both projectors leverage Barco's renowned reliability and innovative design, including features like flexible lens options and easy maintenance functionalities. Their modular architecture allows for straightforward upgrades and repairs, ensuring longevity and reduced cost of ownership.

In conclusion, the Barco R9000893 and R9000896 projectors represent the pinnacle of advanced projection technology, combining high brightness, exceptional image quality, and flexible performance features. These projectors are tailored to meet the rigorous demands of modern visual communication, making them an excellent choice for businesses, event organizers, and creative professionals looking for cutting-edge projection solutions.