Barco R9000893, R9000896 owner manual Options

Page 49

Options

9 OPTIONS

IR Receiver 800

This infrared receiver unit makes it possible to control the BARCOGRAPHICS 1208S from another room.

There is a communication line with cable between the IR receiver and the projector or the RCVDS05. The control information from the RCU can now be sent to this IR receiver.

The IR receiver 800 displays the selected source on a 7-segment display.

Order number : R9827515

Hardwired RCU.

The control signals from the RCU can be sent to the projector via a wired connection.

shield

conductor

Preparing your remote cable :

Use a shielded cable with a maximum length of 100 m and two mini- jack 3.5 mm connectors (order number : R3131991).

-Peel back the vinyl covering of the cable on both sides and twist the wire core.

-Solder a jack plug as shown in drawing above to each end of the cable.

shield = ground

conductor = data information

When the cable is ready, plug one side in the remote control and the other side in the connector on the rear of the projector labelled ‘remote’.

Projector Control software

The software is user-friendly and makes full use of : mouse control, pull down menus and dialog boxes.

Two main applications are available with this software : remote control and transfering and receiving data of projector settings.

Remote Control Simulation. Advantage : address range 0 to 255.

Adjustment Data : where can it be located when a IBM PC (or compatible) or MAC or Workstation is connected :

-hard memory device with files of settings.

-the contents of the local memory of the computer.

-the contents of the projector.

RCVDS 05 Source Selector

An optional RCVDS05 makes it possible to connect up to 20 sources to the projector. When RCVDS's are linked via the expansion module, even 90 inputs can be connected to the projector.

The selected source number will be displayed on a 2 digit display and the selected input module will be indicated with a LED on the rear. Order Numbers RCVDS 05: 110V: 9827888

9827889 220V: 9827880 9827881

VS05 Switcher

The VS05 is a versatile Video and HDTV source selector for all BARCO's digitally controlled large screen projectors. It offers the possibility to connect and switch up to 5 different Video sources, 3 different S-Video sources and 1 RGB Analog source to a BARCO projector. In addition, the audio signal proper to the source, can be switched to an audio amplifier.

Order Numbers:

110V:

9827890

 

220V:

9827899

IRIS/2 Auto-Convergence System

Option for R9000901 and R9000908. Standard available on the both other order numbers.

Easy-to-use, high precision automatic convergence system. Convergence time : less than 2'30''

Various options on the menu offer you the optinal solution for your own individual needs :

-Align : convergence starts from the current image situation

-Align from midposition : convergence starts from midposition

-Touch-up : convergence starts when the source switches or after

a user-defined time : alignment of static convergence almost invisible for the audience.

Order Number: R9828270

5975847 BARCOGRAPHICS 1208S 220197

 

9-1

 

Page 48 Page 50
Image 49
Page 48 Page 50
Contents Graphics 1208s R9000893 R9000896 Date Art. No 220197 R5975847 Barco Projection SystemsNoordlaan Kuurne Belgium Barco nv/Projection SystemsTable of Contents Options Service modeOn safety Safety InstructionsOn cleaning On installationOn servicing On repackingLocation and Function of Controls Stand-by RCU control panel terminologySharpness Power Check AC Power mains Cord ConnectionSwitching On/Off ConnectionsPort No Projector input Press Digit Button Signal Input Connection to the ProjectorComp. Video Video1/Comp. Video Start up with full white imageConnecting a S-Video or Video source to port Connecting a Composite Video source to portVideo input selection Input selectionConnecting a RGB Analog source to port 4/5 Connecting a RGB Analog source to portAnalog Input Selection RGB input selectionRGB analog input terminals with Tri level sync input or Connecting a Component Video source to port 4/5With Tri-level sync on green. The projector detects To select the component video inputConnecting a VS05 switcher to Barcographics 1208s Connecting a Rcvds 05 switcher to the Barcographics 1208sConnecting an IR Remote Receiver to the Barcographics 1208s Controlling Battery installation in the RCUHardware set up of the projector address How to use your RCUHow to control the projector Using your RCUHow to program an address into the RCU? How to display a projector address?Input selection Port No Projector input Press Digit Button Controlling chained projectors Analog Picture ControlsAdjustment Mode Start UP of the Adjustment ModeWrong 0000Overview Random Access Adjustment mode Starting-Up the Random Access Adjustment modeFrom next Internal Cross Hatch Pattern Selecting Setup PatternInternal # Pattern Picture Tuning Random access adjustment mode selection menuColor Balance Clamp Tuning Sync Fast/Slow AdjustmentPeaking Line Doubler option Port 2 Video or S-VideoColor Select Color SelectFocusing Horizontal Phase Adjustment Geometry AdjustmentsGeometry GeometryProjected raster Raster Shift AdjustmentCrt faceplate border Raster ShiftLEFT-RIGHT E-W Left-Right east-west AdjustmentsLEFT-RIGHT Left Side Correction Seagull correctionSeagull Correction Left Side CorrectionTOP-BOTTOM Top-Bottom north-south AdjustmentsTOP-BOTTOM N-S TOP-BOTTOM N-SExit will return to Geometry Horizontal Size AdjustmentVertical Size Adjustment Vertical Linearity AdjustmentTop blanking Right blanking Bottom blanking Blanking AdjustmentsCoarse Convergence Adjustment Convergence AdjustmentConvergence Coarse ConvergenceVertical Corners Fine Convergence AdjustmentOverview flowchart Service mode Starting up the Service modeService Mode Identification Copy ModeCopy a block IdentificationDeletion of blocks Delete ModeDeleting block by block Deletion of all blocksChange Language Change passwordRun time Barcographics 1208SUndo Midposition Set to midpositionConvergence Mid Undo Convergence MidpositionDynamic Astigmatism Dynamic Astigmatism spot shape adjustmentDynamic Astigmatism Gamma corrections G2 AdjustCRT run in cycle Projector Warm Up CRT Drive ModeProjector Warm UP Projector Warm UPFh= 15.6 kHz Fv= 050 Hz MESSAGES, Warnings and Failure Codes003 Input not available RWI commu Nication Error I2C error Addr FH3Iris commu Nication Error Invalid RWI soft VersionOptions Ceiling Mount kit CM100 Magik InterfaceOrbiting Kit Line Doubler KitOrbiting Orbiting Mode Toggle SwitchesOrbiting option Master/Slave ToggleOrbiting Speed Toggle only in Master Orbiting Adjustment procedure Stand-Alone projectorOrbiting Alignment Adjustment procedure multiple projector installations Adjustment Blocks memory blocks Adjustment Blocks and SourceSource numbers 90 Insert Card

R9000896, R9000893 specifications

Barco, a global leader in visualization and collaboration technologies, has introduced several high-performance projectors designed for diverse applications in various sectors, particularly in professional and commercial environments. Among their innovative product lineup, the Barco R9000893 and R9000896 projectors stand out for their impressive features and technological advancements.

The Barco R9000893 is a flagship model that offers exceptional image quality, making it ideal for high-demand applications such as large venue presentations, corporate events, and immersive installations. One of the key characteristics of this projector is its high brightness capability, which enables it to deliver sharp images even in well-lit environments. With a luminosity of up to 40,000 lumens, the R9000893 ensures that every detail of the presentation is visible, enhancing audience engagement.

Equipped with advanced DLP technology, the R9000893 also provides outstanding color accuracy and contrast. This ensures that colors are vibrant and true-to-life, which is particularly important for applications like art installations or product showcases where visual fidelity is paramount. Additionally, the projector boasts a native 4K resolution, allowing for the display of ultra-high-definition content without any compromise on quality.

Similarly, the Barco R9000896, while slightly more compact in design, does not compromise on performance. This model features a similar high brightness capability and offers versatile connectivity options, making it suitable for a wide range of applications, from rental and staging to fixed installations. The R9000896 also includes built-in image processing technologies that enhance image quality and provide seamless scaling of various content formats.

Both projectors leverage Barco's renowned reliability and innovative design, including features like flexible lens options and easy maintenance functionalities. Their modular architecture allows for straightforward upgrades and repairs, ensuring longevity and reduced cost of ownership.

In conclusion, the Barco R9000893 and R9000896 projectors represent the pinnacle of advanced projection technology, combining high brightness, exceptional image quality, and flexible performance features. These projectors are tailored to meet the rigorous demands of modern visual communication, making them an excellent choice for businesses, event organizers, and creative professionals looking for cutting-edge projection solutions.
Top Page Image Contents