Barco R9000896, R9000893 owner manual Projector Warm Up, CRT Drive Mode, Projector Warm UP

Page 46

Service Mode

Projector Warm Up

Highlight 'Projector Warm Up' by pushing the control stick forward or backward and press ENTER to select the projector warm up menu.

The ON/OFF option can be toggled with the ENTER key.

When in the ON position (and the CRT run in cycle is OFF), the projector can start up with a warm up period of 20 minutes. During the start up a warm up menu will displayed. This menu offers the possibility to skip the warm up periode anyway by pressing the EXIT key and offers the possibility to adjust the horizontal and vertical amplitude of the this white image with the control stick. During this warm up period, a full white image is shifted on the CRT faceplate to avoid a burn in.

Every 30 seconds a text box will be displayed on another place on the screen with the remaining time to go.

When EXIT is pressed during this warm up periode, the warm up menu will be redisplayed with the remaining time indication. Press another time EXIT to interrupt the warm up cycle.

When the warm up option is OFF, when switching on the the projector, it starts immediately with the projection of the selected source.

SERVICE MODE

G2 ADJUSTMENT

GAMMA CORRECTIONS

CRT RUN IN CYCLE

PROJECTOR WARM UP

CRT DRIVE MODE

MORE...

PROJECTOR WARM UP

OPTION : ON

A FULL WHITE PATTERN WILL BE GENERATED FOR

20 MINUTES AT POWER UP AFTER THIS PROCEDURE THE PROJECTOR IS READY TO PERFORM IN OPTIMUM

CONDITION

TOGGLE OPTION ON OR OFF

with <ENTER> <EXIT> to return

CRT Drive Mode

The projector CRT's can be driven with the normal current (normal mode), a lower current (economic mode) or with a higher current (boost mode).

To change the drive mode, highlight 'CRT drive mode' by pushing the control stick forward or backward and press ENTER to display the CRT drive mode menu.

To change the boost mode, push the control stick forward or back- ward to select a display mode and press ENTER to select.

The following modes are available :

-normal

-economic : lower drive current to the CRT's, the lifetime of the CRT's will enlarge but the light output will reduce.

-tempory boost : higher drive current to the CRT's, the lifetime of the

CRT's will shorten but the light output will be higher. This situation is tempory, when restarting the projector, the drive mode is auto-

matically set to normal.

-permanent boost : higher drive current to the CRT's, the lifetime of the CRT's will shorten but the light output will be higher. This setting will be saved in the EEPROM. When restarting the projector, it will start up in boost mode.

A warning, permanent BOOST mode in use, will be displayed to inform the user.

When text is on, this warning will be repeated every time a new source is selected.

SERVICE MODE

G2 ADJUSTMENT

GAMMA CORRECTIONS

CRT RUN IN CYCLE

PROJECTOR WARM UP

CRT DRIVE MODE

MORE...

CRT DRIVE MODE

NORMAL

ECONOMIC

TEMPORARY BOOST

PERMANENT BOOST

WARNING : permanent

boost mode reduces the lifetime of the CRT's !

Select with or then <ENTER> <EXIT> to return.

WARNING

PERMANENT

BOOST MODE

IN USE !

7-8

 

5975847 BARCOGRAPHICS 1208S 220197

 

Page 45 Page 47
Image 46
Page 45 Page 47
Contents Graphics 1208s R9000893 R9000896 Barco Projection Systems Date Art. No 220197 R5975847Barco nv/Projection Systems Noordlaan Kuurne BelgiumTable of Contents Service mode OptionsSafety Instructions On safetyOn servicing On installationOn cleaning On repackingLocation and Function of Controls Stand-by RCU control panel terminologySharpness Switching On/Off AC Power mains Cord ConnectionPower Check ConnectionsComp. Video Video1/Comp. Video Signal Input Connection to the ProjectorPort No Projector input Press Digit Button Start up with full white imageVideo input selection Connecting a Composite Video source to portConnecting a S-Video or Video source to port Input selectionAnalog Input Selection Connecting a RGB Analog source to portConnecting a RGB Analog source to port 4/5 RGB input selectionWith Tri-level sync on green. The projector detects Connecting a Component Video source to port 4/5RGB analog input terminals with Tri level sync input or To select the component video inputConnecting a VS05 switcher to Barcographics 1208s Connecting a Rcvds 05 switcher to the Barcographics 1208sConnecting an IR Remote Receiver to the Barcographics 1208s Battery installation in the RCU ControllingHow to control the projector How to use your RCUHardware set up of the projector address Using your RCUHow to program an address into the RCU? How to display a projector address?Input selection Port No Projector input Press Digit Button Analog Picture Controls Controlling chained projectorsStart UP of the Adjustment Mode Adjustment Mode0000 WrongStarting-Up the Random Access Adjustment mode Overview Random Access Adjustment modeFrom next Internal Cross Hatch Pattern Selecting Setup PatternInternal # Pattern Picture Tuning Random access adjustment mode selection menuColor Balance Clamp Tuning Sync Fast/Slow AdjustmentPeaking Color Select Port 2 Video or S-VideoLine Doubler option Color SelectFocusing Geometry Geometry AdjustmentsHorizontal Phase Adjustment GeometryCrt faceplate border Raster Shift AdjustmentProjected raster Raster ShiftLEFT-RIGHT E-W Left-Right east-west AdjustmentsLEFT-RIGHT Seagull Correction Seagull correctionLeft Side Correction Left Side CorrectionTOP-BOTTOM N-S Top-Bottom north-south AdjustmentsTOP-BOTTOM TOP-BOTTOM N-SHorizontal Size Adjustment Exit will return to GeometryVertical Linearity Adjustment Vertical Size AdjustmentBlanking Adjustments Top blanking Right blanking Bottom blankingConvergence Convergence AdjustmentCoarse Convergence Adjustment Coarse ConvergenceFine Convergence Adjustment Vertical CornersOverview flowchart Service mode Starting up the Service modeService Mode Copy a block Copy ModeIdentification IdentificationDeleting block by block Delete ModeDeletion of blocks Deletion of all blocksRun time Change passwordChange Language Barcographics 1208SConvergence Mid Set to midpositionUndo Midposition Undo Convergence MidpositionDynamic Astigmatism Dynamic Astigmatism spot shape adjustmentDynamic Astigmatism Gamma corrections G2 AdjustCRT run in cycle Projector Warm UP CRT Drive ModeProjector Warm Up Projector Warm UPFh= 15.6 kHz Fv= 050 Hz MESSAGES, Warnings and Failure Codes003 Input not available Iris commu Nication Error I2C error Addr FH3RWI commu Nication Error Invalid RWI soft VersionOptions Orbiting Kit Magik InterfaceCeiling Mount kit CM100 Line Doubler KitOrbiting option Orbiting Mode Toggle SwitchesOrbiting Master/Slave ToggleOrbiting Speed Toggle only in Master Orbiting Adjustment procedure Stand-Alone projectorOrbiting Alignment Adjustment procedure multiple projector installations Adjustment Blocks memory blocks Adjustment Blocks and SourceSource numbers 90 Insert Card

R9000896, R9000893 specifications

Barco, a global leader in visualization and collaboration technologies, has introduced several high-performance projectors designed for diverse applications in various sectors, particularly in professional and commercial environments. Among their innovative product lineup, the Barco R9000893 and R9000896 projectors stand out for their impressive features and technological advancements.

The Barco R9000893 is a flagship model that offers exceptional image quality, making it ideal for high-demand applications such as large venue presentations, corporate events, and immersive installations. One of the key characteristics of this projector is its high brightness capability, which enables it to deliver sharp images even in well-lit environments. With a luminosity of up to 40,000 lumens, the R9000893 ensures that every detail of the presentation is visible, enhancing audience engagement.

Equipped with advanced DLP technology, the R9000893 also provides outstanding color accuracy and contrast. This ensures that colors are vibrant and true-to-life, which is particularly important for applications like art installations or product showcases where visual fidelity is paramount. Additionally, the projector boasts a native 4K resolution, allowing for the display of ultra-high-definition content without any compromise on quality.

Similarly, the Barco R9000896, while slightly more compact in design, does not compromise on performance. This model features a similar high brightness capability and offers versatile connectivity options, making it suitable for a wide range of applications, from rental and staging to fixed installations. The R9000896 also includes built-in image processing technologies that enhance image quality and provide seamless scaling of various content formats.

Both projectors leverage Barco's renowned reliability and innovative design, including features like flexible lens options and easy maintenance functionalities. Their modular architecture allows for straightforward upgrades and repairs, ensuring longevity and reduced cost of ownership.

In conclusion, the Barco R9000893 and R9000896 projectors represent the pinnacle of advanced projection technology, combining high brightness, exceptional image quality, and flexible performance features. These projectors are tailored to meet the rigorous demands of modern visual communication, making them an excellent choice for businesses, event organizers, and creative professionals looking for cutting-edge projection solutions.
Top Page Image Contents