Barco R9000896 How to display a projector address?, How to program an address into the RCU?

Page 18

Controlling

How to display a projector address?

With the digit buttons on the RCU, it is possible to select input sources, Video, S-Video, RGsB or RGBS, RG3sB or RGB3S.

Press the ADDRESS key (recessed key on the RCU) with a pencil.

The projector's address will be displayed in a 'Text box'. This text box When a valid and available source is selected, there will be informa- tion displayed on the screen about that source (if "Text" is on). This information includes :

-source number

- horizontal frequency - vertical frequency

PROJECTOR ADDRESS 001

disappears after a few seconds.

 

To continue using your RCU, it is necessary to enter the same

Source 2

Fh= 15.6 kHz

address with the digit buttons (address between 0 and 9). For

Fv= 50 Hz

exemple, if the Adrress Key displays projector address 003, then

 

press the "3" digit button on the RCU to set the RCU's address to

match the projector's address.

When the entry is a non valid source

number, a warning appears on the screen : 'input not available'.

How to program an address into the RCU?

Press the ADDRESS key (recessed key on the RCU) with a pencil and enter the address with the digit buttons. That address can be any digit between 0 and 9.

When programming '0', zero address, the RCU will control a projector regardless of the projector's address. This feature allows multiple projectors with different addresses to be controlled by a single RCU.

Input selection

Port No

Projector input

Press Digit

 

 

 

 

Button

 

 

 

 

 

1

Comp. Video

1

 

2

S-Video1/Comp. Video*

2

 

3

RGB2

3

 

4/5

RGB2

4 or 5

 

4/5

Component video3

6

 

 

 

 

 

 

 

4/5

RGB with Tri level sync4

7

 

 

4/5

Component video

 

 

 

 

with Tri-level sync5

8

 

 

 

 

 

 

Only available when the optional Tri-level sync module is installed.

1Input signal Y/C (luma/chroma)

2Input signal : R, G and B with automatic sync detection between seperate sync (separate composite sync or with separate Hor and Vert. sync) or sync on green (composite sync).

3Input signal : R-Y, Y and B-Y with separate composite sync or with separate Hor and Vert.sync or with composite sync on Y.

4Input signal : R, G and B with separate Tri level sync or with Tri- level sync on green.

5Input signal : R-Y, Y and B-Y with separate Tri level sync or with composite Tri-level sync.

* Video or S-Video : switchable in the PictureTuning menu.

WARNING

input not available

When a valid source number is selected, the projector will display this source or it will wait on the selected source number until the source

WARNING

source not available

becomes available. A message 'source not available' will be dis- played for a short time.

5975847 BARCOGRAPHICS 1208s 220197

 

4-3

 

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Graphics 1208s R9000893 R9000896 Barco Projection Systems Date Art. No 220197 R5975847Barco nv/Projection Systems Noordlaan Kuurne BelgiumTable of Contents Service mode OptionsSafety Instructions On safetyOn servicing On installationOn cleaning On repackingLocation and Function of Controls RCU control panel terminology Stand-bySharpness Switching On/Off AC Power mains Cord ConnectionPower Check ConnectionsComp. Video Video1/Comp. Video Signal Input Connection to the ProjectorPort No Projector input Press Digit Button Start up with full white imageVideo input selection Connecting a Composite Video source to portConnecting a S-Video or Video source to port Input selectionAnalog Input Selection Connecting a RGB Analog source to portConnecting a RGB Analog source to port 4/5 RGB input selectionWith Tri-level sync on green. The projector detects Connecting a Component Video source to port 4/5RGB analog input terminals with Tri level sync input or To select the component video inputConnecting a Rcvds 05 switcher to the Barcographics 1208s Connecting a VS05 switcher to Barcographics 1208sConnecting an IR Remote Receiver to the Barcographics 1208s Battery installation in the RCU ControllingHow to control the projector How to use your RCUHardware set up of the projector address Using your RCUHow to display a projector address? How to program an address into the RCU?Input selection Port No Projector input Press Digit Button Analog Picture Controls Controlling chained projectorsStart UP of the Adjustment Mode Adjustment Mode0000 WrongStarting-Up the Random Access Adjustment mode Overview Random Access Adjustment modeFrom next Selecting Setup Pattern Internal Cross Hatch PatternInternal # Pattern Random access adjustment mode selection menu Picture TuningColor Balance Sync Fast/Slow Adjustment Clamp TuningPeaking Color Select Port 2 Video or S-VideoLine Doubler option Color SelectFocusing Geometry Geometry AdjustmentsHorizontal Phase Adjustment GeometryCrt faceplate border Raster Shift AdjustmentProjected raster Raster ShiftLeft-Right east-west Adjustments LEFT-RIGHT E-WLEFT-RIGHT Seagull Correction Seagull correctionLeft Side Correction Left Side CorrectionTOP-BOTTOM N-S Top-Bottom north-south AdjustmentsTOP-BOTTOM TOP-BOTTOM N-SHorizontal Size Adjustment Exit will return to GeometryVertical Linearity Adjustment Vertical Size AdjustmentBlanking Adjustments Top blanking Right blanking Bottom blankingConvergence Convergence AdjustmentCoarse Convergence Adjustment Coarse ConvergenceFine Convergence Adjustment Vertical CornersStarting up the Service mode Overview flowchart Service modeService Mode Copy a block Copy ModeIdentification IdentificationDeleting block by block Delete ModeDeletion of blocks Deletion of all blocksRun time Change passwordChange Language Barcographics 1208SConvergence Mid Set to midpositionUndo Midposition Undo Convergence MidpositionDynamic Astigmatism spot shape adjustment Dynamic AstigmatismDynamic Astigmatism G2 Adjust Gamma correctionsCRT run in cycle Projector Warm UP CRT Drive ModeProjector Warm Up Projector Warm UPMESSAGES, Warnings and Failure Codes Fh= 15.6 kHz Fv= 050 Hz003 Input not available Iris commu Nication Error I2C error Addr FH3RWI commu Nication Error Invalid RWI soft VersionOptions Orbiting Kit Magik InterfaceCeiling Mount kit CM100 Line Doubler KitOrbiting option Orbiting Mode Toggle SwitchesOrbiting Master/Slave ToggleAdjustment procedure Stand-Alone projector Orbiting Speed Toggle only in Master OrbitingOrbiting Alignment Adjustment procedure multiple projector installations Adjustment Blocks and Source Adjustment Blocks memory blocksSource numbers 90 Insert Card

R9000896, R9000893 specifications

Barco, a global leader in visualization and collaboration technologies, has introduced several high-performance projectors designed for diverse applications in various sectors, particularly in professional and commercial environments. Among their innovative product lineup, the Barco R9000893 and R9000896 projectors stand out for their impressive features and technological advancements.

The Barco R9000893 is a flagship model that offers exceptional image quality, making it ideal for high-demand applications such as large venue presentations, corporate events, and immersive installations. One of the key characteristics of this projector is its high brightness capability, which enables it to deliver sharp images even in well-lit environments. With a luminosity of up to 40,000 lumens, the R9000893 ensures that every detail of the presentation is visible, enhancing audience engagement.

Equipped with advanced DLP technology, the R9000893 also provides outstanding color accuracy and contrast. This ensures that colors are vibrant and true-to-life, which is particularly important for applications like art installations or product showcases where visual fidelity is paramount. Additionally, the projector boasts a native 4K resolution, allowing for the display of ultra-high-definition content without any compromise on quality.

Similarly, the Barco R9000896, while slightly more compact in design, does not compromise on performance. This model features a similar high brightness capability and offers versatile connectivity options, making it suitable for a wide range of applications, from rental and staging to fixed installations. The R9000896 also includes built-in image processing technologies that enhance image quality and provide seamless scaling of various content formats.

Both projectors leverage Barco's renowned reliability and innovative design, including features like flexible lens options and easy maintenance functionalities. Their modular architecture allows for straightforward upgrades and repairs, ensuring longevity and reduced cost of ownership.

In conclusion, the Barco R9000893 and R9000896 projectors represent the pinnacle of advanced projection technology, combining high brightness, exceptional image quality, and flexible performance features. These projectors are tailored to meet the rigorous demands of modern visual communication, making them an excellent choice for businesses, event organizers, and creative professionals looking for cutting-edge projection solutions.
Top Page Image Contents