GN Netcom GN7170 manual Connecting battery, Attaching belt clip, Connecting AC/DC electrical power

Page 6

About the GN 7170’s digital security system. Your GN 7170 uses a digital security system to pro- vide protection against false ringing, unauthorized access and charges to your phone line. When you place the handset into the base unit, the GN 7170 verifies its built-in security code. After a power outage or battery change, place the cordless phone into the base unit for about 20 seconds to automatically reset the built-in security code.

2.3 Connecting battery

Connect the battery by completing the following:

1. Remove the battery compartment door on the cordless phone.

2. Plug the battery cord into the jack located on the inside battery compartment.

3. Replace the battery compartment door.

2.4 Attaching belt clip

Attach the belt clip by completing the following:

1. Insert the sides of the belt clip into the slots on each side of the handset.

2. Snap the ends of the belt clip into place.

2.5 Connecting AC/DC (electrical) power

Note: Before using your GN 7170, you must allow it to charge for

12 hours prior to first use. If you don’t fully charge the GN 7170, battery performance will be compromised.

Do not connect the GN 7170’s telephone line to the modular jack until the GN 7170 has fully charged for 12 hours.

To connect the electrical supply, complete the following:

1. Plug the AC/DC power adapter into the back of the GN 7170’s base unit.

2.Plug the other end of the AC/DC power adapter into an electrical outlet.

•The CHARGE/IN USE indicator will turn on, verifying that the battery is charging.

•The CHARGE/IN USE indicator will not turn on if the cordless phone is not placed in the base correctly.

2.6 Connecting the telephone line and switching the unit on

To connect the telephone line and switch on the unit, complete the following: 1. Plug the GN 7170’s telephone line cord into the TEL LINE jack on the

bottom of the base.

2. Plug the other end of the GN 7170’s telephone line cord into a modular jack in the wall.

3. Set the cordless phone RINGER switch to the ON position.

4. Place the cordless phone into the base unit for charging.

2.7 Assembling and connecting the headset stand and headset

To assemble and connect the headset stand and headset to the cordless phone, complete the following:

1. Insert the flat end of the stand into the slot on the bottom of the base.

6

GN7170_userguide.ind 6

13/08/04 9:55:48

Page 5 Page 7
Image 6
Page 5 Page 7
Contents FIN Contents English GN 7170 user guideDisplay messages and sound signals Transferring CID records to memoryMemory function Product information GN Parts and signaturesInstallation guidelines Setting upInstallation prerequisites Telephone jack requirementsConnecting the telephone line and switching the unit on Connecting batteryConnecting AC/DC electrical power Assembling and connecting the headset stand and headsetFeatures and Customization Telephone operation Ringer Switch CHARGE/IN USE indicatorCanceling instruction *TONE/CANCEL button RedialCall Timer Caller ID CID featuresVolume Call Waiting Caller IDTransferring a CID record to your GN 7170’s memory Transferring CID records to memoryReviewing CID Records Deleting the current CID recordChanging the CID number format Memory functionDialing a Caller ID number Storing a name and number in memoryInserting a pause in the dialing sequence Storing a redial numberDialing a stored number Reviewing and deleting numbersChain dialing from the memory Number for Memory location 0 throughDisplay messages and sound signals Sound signals table MeaningDisplay messages table Meaning Dial tone is OK, but I still can’t dial out Frequently asked questions’ve connected my phone, but there is no dial tone ’m experiencing static/interference during my phone callsOperational and safety information GN7170userguide.ind 13/08/04
Top Page Image Contents