Lucent Technologies Release 3 manual Verify Channel State

Page 66

Channel Mapping

An information screen appears confirming that the switch extension has been mapped to the channel.

9.Press ENTER to continue.

NOTE:

The Voice Equipment screen is not updated until the Channel to PBX Extension screen is closed. If you wish to verify your mapping at any time during the procedure, press the F6 (Cancel) key twice to cancel out of the Channel to PBX Extension and the Assign screen. This will cause the INTUITY system to redraw the Voice Equipment screen.

10.Repeat Steps 6 through 9 for each channel that needs a switch extension.

11.Press F6 (Cancel) until you reach the INTUITY Administration menu.

12.Return to Task 10, "Administer the Lucent INTUITY System for Operation with the MERLIN LEGEND" on page 2-32.

Verify Channel State

The procedure is used to verify that the state of the channel is in-service (Inserv) and that the channels are ready to be tested.

The INTUITY system has four possible port states:

■In-Service (Inserv)

Channel is ready to accept telephone calls. There may be active calls on this channel if the system is operational.

■Facility-out-of-service (Foos)

The channel is not inservice. The Foos state occurs when a channel has been released through the Voice Board Diagnostics screen to Inserv, and it does not detect loop current. A channel in the Foos state should automatically convert to the Inserv state when it detects loop current, but it may need to be reset.

■Manually-out-of-service (Manoos)

The channel has been busied-out under the Voice Board Diagnostics screen, or the channel is on a new IVC6 circuit card. A channel in the Manoos state will remain in the Manoos state until it is released under the Voice Board Diagnostics screen.

■Non-Existent (NONEX or no entry on any screen)

The system does not see the channel. The system will not see a channel that has not been properly activated even if the IVC6 is present. To change a channel from non-existent to recognized, the remote maintenance center must activate it.

A-4Issue 1 June 2000

Page 65 Page 67
Image 66
Page 65 Page 67
Contents Lucent Intuity Copyright  2000, Lucent Technologies All Rights Reserved Contents Channel Mapping Using the Change Extensions Command Vi Issue 1 June Overview Intended AudienceHow this Document Is Organized Conventions Used Document Number Issue Related ResourcesIssue 1 June Trademarks and Service Marks Training How to Make Comments About this Document Conversion Checklist Conversion Checklist Conversion Instructions Select How to Use Lucent Intuity ScreensConversion Procedures EnterTask 2 Deactivate Alarm Origination Task 1 Inventory MaterialsAlarm Management Screen Task 3 Stop the Voice System Information ScreenTask 4 Make an Attended Back-up Tape Backup Screen Do not use the nightly backup tape for this procedure Tape 1 pre-process started Task 5 Remove the Previous Switch Integration Software Example Software Installed ListS25SWIN Task 6 Shutdown the System Task 7 Remove Hardware for the Previous Integration MAP/5 InstructionsMAP/5 Remove the Front Panel Removing the MAP/5 Front Panel MAP/5 Remove the Top Cover 10. Removing the Top Cover on the MAP/5 MAP/5 Locate and Remove the GP Synch or Dciu Circuit Card 11. GP Synch and Dciu Circuit Card FaceplatesMAP/5 Replace the Top Cover and Cables Card can be located in Slot 1, 3, 4, 6, orMAP/40 Instructions MAP/40 Open the MAPPage 13. Remove the Bezel and the Dress Cover Screws 14. Remove the Dress and Access Covers MAP/40 Locate and Remove the GP Synch or Dciu Circuit Card 15. Remove the Retaining BracketMAP/40 Replace the Cover and Cables 16. GP Synch and Dciu Circuit Card FaceplatesMAP/100 Instructions MAP/100 Open the MAPCard cage access door 1/4-turn fasteners MAP/100 Locate and Remove the GP Synch or Dciu Circuit CardMAP/100 Replace the Covers and Cables 18. GP Synch and Dciu Circuit Card FaceplatesTask 8 Allow the System to Finish Booting Task 9 Install the Merlin Legend Switch Integration Software Stop the Voice SystemInstall the Merlin Legend Switch Integration Software Page Start the Voice System Task 11 Shutdown the Lucent Intuity System Task 13 Apply Power to the System Task 14 Test the Channels if the Mapping Changed Task 15 Change the CAS Switch Assignment Task 16 Clear any Alarms 19. Alarm Log Display ScreenTask 17 Place Test Calls to the System Task 18 Assign the System Date and Time20. Set Date and Time Screen Task 19 Stop the Voice System Task 20 Back Up the System-Data Task 21 Start the Voice SystemTask 22 Activate Alarm Origination 21. Alarm Management Screen22. Alarm Origination Menu 25. Alarm Origination Test Results Screen Task 23 Create a Test Alarm 26. Audix Administration Screen Task 24 Replace the Nightly Backup Tape Task 25 Remove the Old Software from the Site48Issue 1 June Administer the Intuity Switch Interface Map Channels to Switch ExtensionsPage Figure A-2. Assign Screen Verify Channel State Figure A-4. Voice Equipment Screen Figure A-5. Diagnose Voice Equipment Screen Figure A-6. Release of Voice Equipment Screen Assign Service to Channels for Testing Figure A-7. Voice Equipment ScreenFigure A-9. Assign Services to Voice Channels Screen Test Each Channel Test Each Channel These are different voice encoding algorithms Assign Services to Called Numbers Figure A-11. Voice Equipment Screen Figure A-13. Assign Service to Called Number Screen Page Map Services to Channels for Operation Figure A-15. Assign ScreenPage Page Channel Mapping 20Issue 1 June Using the Change Extensions Command Busyout the Voice Ports Figure B-1. Diagnose Voice Equipment ScreenBusyout the Networking Ports Number of the last cardFigure B-3. Busyout Networking Channel Screen Stop the Voice System Changing a Block of Extensions With Extension Length Change Change extensions Ch eFigure B-4. Change Extension Screen 8Issue 1 June Change extensions Ch e Figure B-5. Change Extension Screen Page Release the Voice Ports Figure B-6. Diagnose Voice Equipment ScreenFigure B-7. Release of Voice Equipment Screen Release the Networking Ports Figure B-8. Release Networking Channel Screen

Release 3 specifications

Lucent Technologies Release 3 was a significant milestone in the evolution of telecommunications. Launched in the late 1990s, it represented a comprehensive suite of solutions designed to improve network performance, reliability, and scalability. Aimed primarily at enhancing communication services, Release 3 showcased advanced technologies and features that reshaped the industry landscape.

One of the standout features of Release 3 was its support for both circuit-switched and packet-switched networks. This dual capability allowed service providers to utilize a single platform to provide a variety of services, including traditional voice services and emerging data applications. The integration of these two technologies led to more efficient use of network resources and improved service quality.

Release 3 also emphasized flexibility and modularity. Its architecture was designed to support a range of hardware and software configurations, enabling telecom operators to customize their deployments according to specific business needs. This modular design allowed for easier upgrades and scaling, which was essential as the demand for bandwidth and services continued to grow.

Another key technology featured in Release 3 was its advanced signaling and control capabilities. By implementing protocols like SS7 and integrating them with IP-based communications, Lucent enabled more efficient call routing and management. This capability was critical for managing increasing traffic loads and offering enhanced features like caller ID, call waiting, and other value-added services that were becoming popular at that time.

In addition, Release 3 introduced improved quality of service (QoS) mechanisms, critical for ensuring that voice and data services could coexist on the same network without degradation. This was especially important as the world began to embrace the Internet, leading to a surge in data-intensive applications that needed reliable delivery.

Security was another focus with Release 3, as telecom operators faced growing concerns about fraud and cyber threats. Enhanced encryption methods and secure access controls were built into the system, providing operators with the tools needed to safeguard their networks and customer data.

Overall, Lucent Technologies Release 3 represented a forward-looking approach to telecommunications, combining innovative technology with the flexibility needed in a rapidly changing industry. It laid the groundwork for future advancements in both voice and data communications, helping operators to adapt to the burgeoning digital landscape. As a result, it played a pivotal role in the transition towards more integrated and efficient telecommunication networks.
Top Page Image Contents