Lucent Technologies Release 3 manual Stop the Voice System

Page 87

Stop the Voice System

Stop the Voice System

The following procedure describes how to stop the Lucent INTUITY voice system.

1.Starting at the Lucent INTUITY Administration menu, select:

>Customer/Services Administration

>System Management

>System Control

>Stop Voice System

The system displays the following prompt:

Enter y to continue, n to quit.

2. Enter y

The system stops the voice system and returns to the System Control screen. If the system displays the following message:

The Voice System has stopped.

Press ENTER to continue.

press ENTER to return to the System Control screen.

3.Press F6 (Cancel) three times to return to the Lucent INTUITY Administration menu.

4.Determine your next step:

■If you want to change the length of local extension numbers, continue with “Changing a Block of Extensions (with Extension Length Change)”.

■If you want to change a block of extensions, continue with "Changing a Block of Extensions (without Extension Length Change)" on page B-9”.

Issue 1 June 2000 B-5

Page 86 Page 88
Image 87
Page 86 Page 88
Contents Lucent Intuity Copyright  2000, Lucent Technologies All Rights Reserved Contents Channel Mapping Using the Change Extensions Command Vi Issue 1 June Overview Intended AudienceHow this Document Is Organized Conventions Used Related Resources Document Number IssueIssue 1 June Trademarks and Service Marks Training How to Make Comments About this Document Conversion Checklist Conversion Checklist Conversion Instructions Enter How to Use Lucent Intuity ScreensConversion Procedures SelectTask 1 Inventory Materials Task 2 Deactivate Alarm OriginationAlarm Management Screen Information Screen Task 3 Stop the Voice SystemTask 4 Make an Attended Back-up Tape Backup Screen Do not use the nightly backup tape for this procedure Tape 1 pre-process started Example Software Installed List Task 5 Remove the Previous Switch Integration SoftwareS25SWIN Task 6 Shutdown the System Task 7 Remove Hardware for the Previous Integration MAP/5 InstructionsMAP/5 Remove the Front Panel Removing the MAP/5 Front Panel MAP/5 Remove the Top Cover 10. Removing the Top Cover on the MAP/5 11. GP Synch and Dciu Circuit Card Faceplates MAP/5 Locate and Remove the GP Synch or Dciu Circuit CardCard can be located in Slot 1, 3, 4, 6, or MAP/5 Replace the Top Cover and CablesMAP/40 Open the MAP MAP/40 InstructionsPage 13. Remove the Bezel and the Dress Cover Screws 14. Remove the Dress and Access Covers 15. Remove the Retaining Bracket MAP/40 Locate and Remove the GP Synch or Dciu Circuit Card16. GP Synch and Dciu Circuit Card Faceplates MAP/40 Replace the Cover and CablesMAP/100 Open the MAP MAP/100 InstructionsMAP/100 Locate and Remove the GP Synch or Dciu Circuit Card Card cage access door 1/4-turn fasteners18. GP Synch and Dciu Circuit Card Faceplates MAP/100 Replace the Covers and CablesTask 8 Allow the System to Finish Booting Stop the Voice System Task 9 Install the Merlin Legend Switch Integration SoftwareInstall the Merlin Legend Switch Integration Software Page Start the Voice System Task 11 Shutdown the Lucent Intuity System Task 13 Apply Power to the System Task 14 Test the Channels if the Mapping Changed Task 15 Change the CAS Switch Assignment 19. Alarm Log Display Screen Task 16 Clear any AlarmsTask 18 Assign the System Date and Time Task 17 Place Test Calls to the System20. Set Date and Time Screen Task 19 Stop the Voice System Task 21 Start the Voice System Task 20 Back Up the System-Data21. Alarm Management Screen Task 22 Activate Alarm Origination22. Alarm Origination Menu 25. Alarm Origination Test Results Screen Task 23 Create a Test Alarm 26. Audix Administration Screen Task 25 Remove the Old Software from the Site Task 24 Replace the Nightly Backup Tape48Issue 1 June Map Channels to Switch Extensions Administer the Intuity Switch InterfacePage Figure A-2. Assign Screen Verify Channel State Figure A-4. Voice Equipment Screen Figure A-5. Diagnose Voice Equipment Screen Figure A-6. Release of Voice Equipment Screen Figure A-7. Voice Equipment Screen Assign Service to Channels for TestingFigure A-9. Assign Services to Voice Channels Screen Test Each Channel Test Each Channel These are different voice encoding algorithms Assign Services to Called Numbers Figure A-11. Voice Equipment Screen Figure A-13. Assign Service to Called Number Screen Page Figure A-15. Assign Screen Map Services to Channels for OperationPage Page Channel Mapping 20Issue 1 June Using the Change Extensions Command Figure B-1. Diagnose Voice Equipment Screen Busyout the Voice PortsNumber of the last card Busyout the Networking PortsFigure B-3. Busyout Networking Channel Screen Stop the Voice System Change extensions Ch e Changing a Block of Extensions With Extension Length ChangeFigure B-4. Change Extension Screen 8Issue 1 June Change extensions Ch e Figure B-5. Change Extension Screen Page Figure B-6. Diagnose Voice Equipment Screen Release the Voice PortsFigure B-7. Release of Voice Equipment Screen Figure B-8. Release Networking Channel Screen Release the Networking Ports

Release 3 specifications

Lucent Technologies Release 3 was a significant milestone in the evolution of telecommunications. Launched in the late 1990s, it represented a comprehensive suite of solutions designed to improve network performance, reliability, and scalability. Aimed primarily at enhancing communication services, Release 3 showcased advanced technologies and features that reshaped the industry landscape.

One of the standout features of Release 3 was its support for both circuit-switched and packet-switched networks. This dual capability allowed service providers to utilize a single platform to provide a variety of services, including traditional voice services and emerging data applications. The integration of these two technologies led to more efficient use of network resources and improved service quality.

Release 3 also emphasized flexibility and modularity. Its architecture was designed to support a range of hardware and software configurations, enabling telecom operators to customize their deployments according to specific business needs. This modular design allowed for easier upgrades and scaling, which was essential as the demand for bandwidth and services continued to grow.

Another key technology featured in Release 3 was its advanced signaling and control capabilities. By implementing protocols like SS7 and integrating them with IP-based communications, Lucent enabled more efficient call routing and management. This capability was critical for managing increasing traffic loads and offering enhanced features like caller ID, call waiting, and other value-added services that were becoming popular at that time.

In addition, Release 3 introduced improved quality of service (QoS) mechanisms, critical for ensuring that voice and data services could coexist on the same network without degradation. This was especially important as the world began to embrace the Internet, leading to a surge in data-intensive applications that needed reliable delivery.

Security was another focus with Release 3, as telecom operators faced growing concerns about fraud and cyber threats. Enhanced encryption methods and secure access controls were built into the system, providing operators with the tools needed to safeguard their networks and customer data.

Overall, Lucent Technologies Release 3 represented a forward-looking approach to telecommunications, combining innovative technology with the flexibility needed in a rapidly changing industry. It laid the groundwork for future advancements in both voice and data communications, helping operators to adapt to the burgeoning digital landscape. As a result, it played a pivotal role in the transition towards more integrated and efficient telecommunication networks.
Top Page Image Contents