Lenoxx Electronics PH559 Hands-Free Speakerphone Operation, Volume Control and Ringer Setting

Page 11

Hands-Free (Speakerphone) Operation

ANSWERING CALLS WITH THE SPEAKERPHONE

1.After the phone rings twice, press the SPEAKER button, the SPEAKERPHONE

INDICATOR will light, and the hook icon will show in the display.

2.The display will show the Count Up Call Timer after a few seconds.

3.Adjust the speakerphone volume by sliding the SPEAKER VOLUME control on the right side of the phone.

4.To end the call, press the SPEAKER button again.

5.The SPEAKERPHONE INDICATOR will go off and the display will return to Time and Date mode.

MAKING CALLS WITH THE SPEAKERPHONE

1.Press the SPEAKER button to get a dial tone - no need to lift the handset.

2.The SPEAKERPHONE INDICATOR will light and the hook icon will show in the display, the Count Up Timer will start after a few seconds.

3.Adjust the speakerphone volume by sliding the SPEAKER VOLUME control on the right side of the phone.

4.Dial your call.

5.To end the call, press the SPEAKER button again.

6.The SPEAKERPHONE INDICATOR will go off and the display will return to Time and Date mode.

NOTE: When pick up the HANDSET or press the SPEAKER button, the hook icon will show in the display. If this icon shows in the display while the phone is not in use, remember to check if the HANDSET is replaced properly or the SPEAKER button is pressed to off.

Volume Control and Ringer Setting

Adjust the handset volume

Slide the HANDSET VOLUME control (LOUD or NORMAL).

 

 

Adjust the ringer ON

Set RINGER ON/OFF switch.

or OFF

ON - Normal setting, the phone rings on incoming calls.

 

OFF - To turn off the ringer, for undisturbed privacy.

 

NOTE: Only this phone will not ring, other phones on the

 

same line will continue to ring normally.

If you have subscribed to the Caller ID service, the caller’s number and/or name appears on the display when you received a call (see page 11).

Last Number Redialing and Pause Function

1.Pick up the HANDSET or press the SPEAKERPHONE button. The hook icon will show in the display.

2.Press the REDIAL/PAUSE button. The last dialed number appears in the display and is automatically dialed.

TO CHECK THE LAST PHONE NUMBER DIALED

While the handset is on the base, press the REDIAL/PAUSE button. The number appears in the display for 3 seconds.

NOTE: If the last dialed number exceeds 16 digits, only 16 digits will be displayed.

PAUSE FUNCTION

Example: In an office where you need to dial a 9 first to get an outside line.

Dial the number 9 and press REDIAL/PAUSE button, and then dial the phone number. You will see a “ ” displayed for pause. You may also store this into memory.

9IB-PH559(9803C)-WM-E-042602

Image 11
Contents Operating Instructions Memory Call Waiting Caller ID Speaker TelephoneTable of Contents Important Safety Instructions For customer serviceBattery Safety Instructions Important Telephone Company & FCC Information 18 19 20 Location of ControlsGetting Started Checking the Package ContentsUsing Batteries Powering the PhoneSetting UP LCD CONTRAST, LANGUAGE, Area CODE, Time and Date Telephone InstallationSetting up the Telephone Connecting the TelephoneMaking a Call BasicsChoosing Tone or Pulse Dialing Making and Receiving CallsLast Number Redialing and Pause Function Volume Control and Ringer SettingHands-Free Speakerphone Operation Memory Dialing Telephone FeaturesViewing the Caller ID List Caller ID Features Understanding the Caller ID ServiceWhen You Received a Call Call WaitingStoring the Phone Numbers from the Caller ID List Caller ID FeaturesCalling Back From the Caller ID List Deleting the Data from the Caller ID List Using Message Waiting/MailboxSlide OUT Reverse Replace Into Phone Wall MountingP O R TA N T Installation on MasonryTrouble Shooting Trouble Shooting Limited Warranty