Teledex manual CL2100 Series Telephone Diagram

CL2100 SERIES TELEPHONE DIAGRAM

Charge LED Message Waiting Lamp

PREPARING TO USE THE CL2100 SERIES TELEPHONE

BASE PREPARATION PROCEDURE

1)	Insert either end of the RJ-45 cable into the jack on the back of the telephone labeled
	“LINE.”
2)	Insert the other end of the cable into the jack on the AC adapter labeled “PHONE.”
Note: The base may emit a “beep” tone when the power is switched on.

Hold Key

Flash Programming Keys

100 ms

300 ms

600 ms

3)	Insert one end of the RJ-11 line cord into the jack on the AC adapter labeled “LINE.”
4)	Insert the other end of this line cord into a telephone wall outlet jack.
5)	Plug the AC adapter into an available, unswitched electrical wall outlet.
6)	Remove the plastic overlay and place the paper faceplate over the keys. Replace the
	plastic overlay by hooking the tabs on the overlay into the recessed slots located on
	both sides.

Line	Store Key
On/Off
	Programmimg Port
Keys

Auto Dial Keys

Conf.						M1 - M5 (model CL2105)
						M1 - M10 (model CL2110)
	Volume
	Keys
Flash
						DTMF Keys
Redial
						Volume Keys
						Paging Key
						Mute
						Redial
						Speakerphone
		Hold
			Line 1	Line 2	Conference

EC DECLARATION OF CONFORMITY

This product has been certified by an independent, accredited test house that it complies with the requirements of the following directives:

•European Community Directive 73/23/EEC and 93/68/EEC, based on the standards: EN 60950:1992+A1+A2+A3+A4+A11 / EN 41003:1998

Test report Nr.: G0M20106-4905-L Dated: June 19, 2001

• R&TTE Directive 1999/5/EC on the approximation of the laws of the member states relating to network connection and radio spectrum matters, based on the following standards: I-CTR 37 (1998) TBR 10 (1997) TBR 6 (1997)

•R&TTE Directive 1999/5/EC and Council Directive 89/336/EEC on the approximation of the laws of the member states relating to electromagnetic compatibility, based on the following standards: EN 301 489-1/-6, EN 50081-1, EN 50082-1

CONGRATULATIONS AND THANK YOU

Congratulations on your purchase of this high-quality, Teledex-made European ETSI DECT-based hospitality guestroom cordless telephone. Teledex LLC is the world's leading hospitality telephone supplier, with over five million phones shipped worldwide. If you have any questions about this telephone, please feel free to contact us via one of the methods below. We appreciate your purchase!

CONTACTING TELEDEX

Telephone:	01.408.363.3100	Address: 6311 San Ignacio Avenue
Internet:	www.teledex.com	San Jose, CA 95119
email:	sales@teledex.com	USA

part number 600-0480-48A

Hint: The overlay is easiest to insert when the left or right side tabs are inserted first, and the middle of the overlay is slightly bowed to allow for insertion of the other tabs.

7)Place the cordless handset on the base unit.

Note: The speakerphone may turn on and speakerphone LED illuminate when the base unit is first powered on. Press the Speakerphone “On/Off” button to reset the speakerphone to the off position.

HANDSET PREPARATION PROCEDURE

1)Prepare to install the battery into the handset by first removing the rubber screw cover and the screw beneath. Then firmly press down on the top of the battery compartment cover and slide it towards the bottom of the handset until it is removed.

2)Insert the battery connector into the connector inside the handset.

3)Replace the battery compartment cover, retaining screw and rubber screw cover. Note: The handset may emit a “beep” tone when the battery is connected. The “ON” key will blink to indicate the handset is searching for the base. It will stop blinking when the handset is registered to base. This is an indication that the telephone is ready to be used. To ensure optimal performance of the telephone charge the battery overnight. See charging details under “Charging the Battery.”

BASE – HANDSET REGISTRATION PROCEDURE (FOR HOTEL TECHNICAL SERVICE PERSONNEL ONLY)

To register the CL2100 series handset to the base:

1)Press and hold the “CONF” key until a running light appears on the handset “Line 1,” “Line 2” and “CONF” LED’s.

2)Press the numbers 4, 5 and 6 (in sequence) on the keypad. The “Line 1,” “Line 2” and “CONF” LED’s will be flashing. Immediately press and hold both the “PAGE” key and the “HOLD” key on the base simultaneously, until two continuous beeps are heard from the base unit. When a link between the base and handset is established, the “Line 1” and “Line” 2 LED’s on handset will be in a steady “on” state. When both LED’s turn off, the registration procedure is completed.

3)To confirm the handset is successfully registered to the base, press the “PAGE” key on the base. The handset will beep for a short period. The handset will stop beeping if it is answered, by pressing the “Line1” or “Line 2” keys on the handset, or by pressing the “PAGE” key on the base again.

CHARGING THE BATTERY

The rechargeable Nickel Metal Hydride battery must be fully charged before using the phone for the first time. It is recommended that the battery pack be charged overnight

1