Intel DG33TL manual Remove the Processor from the Protective Processor Cover

Page 31

Installing and Replacing Desktop Board Components

5.Remove the processor from the protective processor cover. Hold the processor only at the edges, being careful not to touch the bottom of the processor (see Figure 9). Do not discard the protective processor cover. Always replace the processor cover if the processor is removed from the socket.

Figure 9. Remove the Processor from the Protective Processor Cover

6.Hold the processor with your thumb and index fingers oriented as shown in

Figure 10. Make sure your fingers align to the socket cutouts (Figure 10, A). Align notches (Figure 10, B) with the socket (Figure 10, C). Lower the processor straight down without tilting or sliding it in the socket.

Figure 10. Install the Processor

31

Image 31
Contents Intel Desktop Board DG33TL Product Guide Disclaimer Revision HistoryFCC Declaration of Conformity Canadian Department of Communications Compliance StatementDocument Organization PrefaceIntended Audience Use Only for Intended ApplicationsTerminology Box ContentsContents Updating the Bios Regulatory Compliance ContentsTables Feature Summary Desktop Board FeaturesHardware Power ManagementSupported Operating Systems Related LinksDesktop Board Components Desktop Board FeaturesLabel Description Main Memory ProcessorType Timing Intel G33 Express ChipsetGMA 3100 Graphics Controller Intel G33 Graphics SubsystemAudio Subsystem PCI Express x16 Connector DVI Port VGA PortDVI/VGA Port Status Legacy Input/Output I/O Controller RJ-45 LAN Connector LEDsLAN Subsystem Enhanced IDE Interface Hi-Speed USB 2.0 SupportLED Color LED State Indicates Expandability Serial ATA and IDE Auto ConfigurationPCI and PCI Express* Auto Configuration Serial ATASecurity Passwords Hardware Management FeaturesHardware Monitoring and Fan Speed Control Chassis Intrusion Power Management FeaturesHardware Support Fan Headers +5 V Standby Power Indicator LED Energy STAR* Qualified BatterySpeaker Real-Time ClockBefore You Begin Installing and Replacing Desktop Board ComponentsPrevent Power Supply Overload Installation PrecautionsObserve Safety and Regulatory Requirements Installing and Replacing Desktop Board Components Installing the I/O ShieldDesktop Board DG33TL Mounting Screw Hole Locations Installing and Removing the Desktop BoardInstalling a Processor Installing and Removing a ProcessorLift the Load Plate Remove the Processor from the Protective Processor Cover Close the Load Plate Installing the Processor Fan Heat SinkConnecting the Processor Fan Heat Sink Cable Removing the Processor Installing and Removing MemoryDual Channel Memory Configuration with Two DIMMs Guidelines for Dual Channel Memory ConfigurationThree DIMMs Use DDR2 DIMMs Installing DIMMsInstalling a Dimm Removing DIMMs Installing a PCI Express x16 Card Installing and Removing a PCI Express x16 CardRemoving a PCI Express x16 Card Removing the PCI Express x16 CardConnecting the IDE Cable Connecting the IDE Cable Connecting a Serial ATA Cable Connecting the Serial ATA Sata CablesConnecting the External Serial ATA Adapter Bracket Installing the External Serial ATA Adapter BracketInternal Headers Connecting to the Internal HeadersIeee 1394a Signal Header Names Connecting to the HD Audio Link HeaderConnecting to the Ieee 1394a Header HD Audio Link Header Signal NamesPin Signal Name Ground Connecting to the Consumer IR CIR HeadersFront Panel CIR Receiver Input Header Signal Names Back Panel CIR Header Emitter Output Header Signal NamesConnecting to the Chassis Intrusion Header Connecting to the Serial Port HeaderConnecting to the Alternate Front Panel Power LED Header Front Panel Header Connecting to the Front Panel HeaderConnecting to the USB 2.0 Headers USB 2.0 Header Signal NamesBack Panel Audio Connectors Connecting to the Flexible Audio SystemConnecting Chassis Fan Cables Connecting Chassis Fan and Power Supply CablesConnecting Power Supply Cables Connecting Supply Power CablesLocation of the Bios Configuration Jumper Block Setting the Bios Configuration JumperJumper Setting Mode Description Jumper Settings for the Bios Setup Program ModesClearing Passwords Precaution Replacing the BatteryΠροσοχή Vigyazat Uyari Removing the Battery Intel Desktop Board DG33TL Product Guide Updating the Bios with the Intel Express Bios Update Utility Updating the BiosUpdating the Bios with the ISO Image Bios Update File Obtaining the Bios Update FileUpdating the Bios Updating the Bios with the Iflash Memory Update UtilityRecovering the Bios Configuring the Bios for Intel Matrix Storage Technology Configuring for RAID Intel Matrix Storage TechnologyCreating Your RAID Set Setting Up a RAID Ready System Bios Error Messages Error Messages and IndicatorsBios Beep Codes Bios Error MessagesIntel Desktop Board DG33TL Product Guide Regulatory Compliance Safety RegulationsPlace Battery Marking Safety RegulationsEuropean Union Declaration of Conformity Statement Regulatory Compliance Español Product Ecology StatementsRecycling Considerations DeutschRussian FrançaisMalay PortugueseTürkçe Lead-Free Desktop BoardLead-Free Board Markings EMC Regulations EMC RegulationsEnsure Electromagnetic Compatibility EMC Compliance Board-Level Certification Markings Product CertificationsProduct Certification Markings Europe Chassis and Component CertificationsIntel Desktop Board DG33TL Product Guide