Siemens A30853 operating instructions Displaying the software version

Page 48

27.11.98

kap01.fm5

Profiset 30isdn engl.: A30853-X300-B107-1-7619

Programming the telephone settings

Restoring the as-supplied condition

a

S26

T

0or 1

S

The Profiset 30isdn can be reset to the default settings.

To restore the as-supplied condition, it is absolutely nec- essary to enter the password, also if it is still programmed to 0000.

Enter 1 to restore the as-supplied condition (or 0 for no reset):

●“1“ Restore the as-supplied condition.

● “0“ Do not restore the as-supplied condition.

Handset is on-hook.

Start the programming procedure.

Enter the password.

Press key 0 or 1.

Exit the programming procedure.

Note:

If you restore the as-supplied condition, all pro- grammed numbers and changed settings are cleared.

Displaying the software version

a

T S27

If you contact the Siemens Service (➔ page 44) please tell them the number of your software version as thus makes the correction of defects a lot easier.

Handset is on-hook.

Enter the password if necessary.

Start the programming procedure.

Software version is indicated on the display.

SDisplay of software version is switched off.

40

Image 48

Contents Profiset 30isdn Profiset 30isdn Profiset 30isdnYour guide to this manual Profiset 30isdn Overview Profiset 30isdn Profiset 30isdn Overview Keys Safety precautions and approval Safety precautionsLocation of the telephone Profiset 30isdn Approval and conformity Contents Contents Symbols used in these operating instructions Putting the telephone into operationPutting the telephone into operation Isdn connecting cord Handset cord coiled Telephone connecting cord Putting the telephone into operation Connect the telephoneHandset cord coiled Program the multiple subscriber numbers MSNs NtbaSetting the national variants PBX operation only Program the trunk codePutting the telephone into operation Try out the telephone Calling another partyTaking a call Symbols Digit display line Display Idle modeDisplay-driven telephone operation Display-driven telephone operationConnected mode 030234577 001.20 045672343Outgoing and incoming calls Outgoing and incoming callsCalling users On-hook dialling Outgoing and incoming calls Number redial automatic dialling Is displayed Outgoing and incoming calls Accepting a call Rejecting a call DisconnectCall forwarding Deactivating the call signal Do not disturb Outgoing and incoming calls Call waitingAccepting call waiting Rejecting call waitingOutgoing and incoming calls Call list Retrieving entries from the call listDialling a number from the call list Storing a number from the call listCallback Deleting the call listInitiating a callback Ending a call disconnecting Accepting a callbackClearing a callback Switching to mute consultation in the room Convenient and secure telephone communicationConvenient and secure telephone communication Activating/deactivating open listeningConvenient and secure telephone communication Parking a call Resuming a parked call27.11.98 Kap01.fm5 Keypad signalling Dtmf Switching between two calling parties toggling Calls involving two or more partiesCalls involving two or more parties Calling the second party consultationDisconnecting one party Three-party conferenceEnding a conference by disconnecting a party Calls involving two or more parties Ending a conferenceEnding a conference and toggling between parties Exiting from a conferenceProgramming keys on the telephone Programming keys on the telephoneProgramming the destination dialling keys Programming the speed dialling keysProgramming direct station selection babyphone Quick reference for available telephone settings Quick reference for available telephone settingsTelephone settings DescriptionProgramming the telephone settings Programming the telephone settingsPassword Programming the telephone settings Ringer volume Ringer melodyS06 T 0 or Following settings are possible Call processing typeMultiple Subscriber Numbers MSN Programming the telephone settings National variants 27.11.98 Kap01.fm5 Date/time Call number for call forwarding unconditionalEnter the call number for call forwarding Save the setting Tariff unit factorCall is deactivated Clearing the summation meter S14 TEnabling/disabling call waiting Programming the telephone settings Clearing memory Checking the settings statusDisplaying the software version Important information for installation and operation Important information for installation and operationMaintenance Removing and inserting the labelling cardsDefault settings Technical dataThird party use/disposal Siemens Service Symptom Cause Action Isdn glossary Isdn glossaryIsdn glossary Isdn glossary Quick reference guide Quick reference guideToggling d è R è R Quick reference for available telephone settings Index IndexTechnical data 27.11.98 Back.fm5 Siemens Aktiengesellschaft