AeroComm ZB2430 manual Eeprom Byte Write, Restore Factory Defaults, Soft Reset with NV reset

Page 41

3 6

C O N F I G U R I N G T H E Z B 2 4 3 0

Upon receiving this command, a transceiver will respond with the desired data from the addresses requested by the OEM Host. *Note: Maximum Length is 0xFC.

Command: <0xCC> <0xC0> <Start> <Length>

Number of Bytes Returned: 4+

Response: <0xCC> <Start> <Length> <Data>

Parameter Range:

<Start>

= EEPROM address to begin reading at

<Length>

=

Length of data to be read

<Data>

=

Requested data

 

 

 

EEPROM Byte Write

Upon receiving this command, a transceiver will write the data bytes to the specified address but will not respond to the OEM Host until the EEPROM write cycle is complete.

Note: The maximum length of data that can be written in a single write process is 0x50. If writing the entire 256-byte EEPROM, it is convenient to perform 64 byte (0x40) writes.

Command: <0xCC> <0xC1> <Start> <Length> <Data>

Number of Bytes Returned: 3

Response: <Start> <Length> <Last byte>

Parameter Range:

<Start>

=

EEPROM address to begin writing at

<Length>

=

Length of data to be written (Max = 0x50)

<Data>

=

Data to be written

<Last byte> =

Value of last byte written

 

 

 

Reset

The OEM Host issues this command to perform a soft reset of the transceiver. Any transceiver settings modified by CC commands will revert to the values stored in the EEPROM.

Command: <0xCC> <0xFF>

Number of Bytes Returned: None

Response: None

Restore Factory Defaults

The OEM Host issues this command to restore the EEPROM Configuration to factory default.

*Note. This command does not perform a NV Reset.

Command: <0xCC> <0xFF> <0xDF>

Number of Bytes Returned: None

Response: None

Soft Reset with NV reset

The OEM Host issues this command to perform a soft reset of the transceiver and to erase the network settings stored in the radio’s non-volatile memory. Any transceiver settings modified by CC commands will revert to the values stored in the EEPROM.

Command: <0xCC> <0xFF> <0xE3>

Number of Bytes Returned: None

Response: None

Page 40 Page 42
Image 41
Page 40 Page 42
Contents VE R S I O N Sales Technical SupportDocument Information Limited Warranty, Disclaimer, Limitation of LiabilityCopyright 2008 AeroComm, Inc. All rights reserved This material is preliminaryRevision Description Revision HistoryContents E R V I E W ZB2430 Transceiver Module2 4 3 0 F E a T U R E S B l e 1 Z B 2 4 3 0 Specification s SpecificationsGeneral PhysicalCertifications N D E F I N I T I O N S SMT Pin Pluggable Type Signal Name FunctionCTS Design NotesHardware Interface I n E e p I n dTerms & Definitions TE R M S & D E F I N IT I O N S TE R MS & D E F in I TI O N S E E 8 0 2 5 & Z I G B E E O V E R V I E W Theory of OperationCoordinator RouterS h E a T I N G a N E T W O R KEnd Device G u r e 1 Z i g B e e N e t w o r k T o p o l o g i e s R E N T / C H I L D R E L a T I O N S H I PX i m u m N e t w o r k D e p t h T W O R K L I M I T a T I O N SG u r e 2 P a r e n t / C h i l d R e l a t i o n s h i p I t N e t w o r k a d d r e s s G B E E a D D R E S S I N GB l e 3 D e v i c e T a b l e E x a m p l e I t M a C a d d r e s sS h R o u t i n g a O D Bit Network AddressesZB2430 User’s Manual O a d c a s t T r a n s m i s s i o n s Broadcast Address Destination Group B l e 4 B r o a d c a s t a d d r e s s e sSending a Broadcast packet T E R F a C E M O D E S Serial InterfaceA n s p a r e n t M o d e I M o d eB l e 5 B a u d R a t e / I n t e r f a c e T i m e o u t R I a L I N T E R F a C E B a U D R a T EO W C O N T R O L Using a non-standard baud rateT E R F a C E T I M E O U T / R F P a C K E T S I Z E D D a t a B u f f e r a n d R T S D D a t a B u f f e r a n d C T SExamples T W O R K I N GZB2430 User’s Manual B l e 7 S l e e p M o d e S e t t i n g s W E R D O W N M O D E SC l i c S l e e p E p S l e e pTransmitting and Receiving data with a sleeping End Device G u r e 1 1 Z B 2 4 3 0 C o n f i g u r a t i o n F l o w Configuring the ZB2430B l e 8 C o m m a n d Q u i c k R e f e r e n c e C O M M a N D ST h e F l y C o n t r o l C o m m a n d s N F I G U R I N G T H E Z B 2 4 3 M M a N D D E S C R I P T I O N S Auto Destination Read Destination AddressRead API Control Write API ControlRead Digital Input Set Max PowerRead ADC Write Digital OutputsRead 16-bit NWK Address of Parent Device Read 16-bit NWK AddressDiscover 16-bit NWK Address of Remote Radio Discover Ieee Address of Remote RadioDiscover Ieee Address & Children of Remote Radio Read TemperatureRead Voltage Eeprom Byte ReadRestore Factory Defaults ResetSoft Reset with NV reset Eeprom Byte WriteParameter Length Range Default Description Address BytesEeprom Parameters Bytes Length Range Default Description AddressZB2430-Q ZB2430-D MAC ID I T r a n s m i t P a c k e t API OperationG u r e 1 2 T r a n s m i t a P I p a c k e t f o r m a t I S e n d D a t a C o m p l e t eG u r e 1 4 R e c e i v e a P I p a c k e t f o r m a t I R e c e i v e P a c k e tZB2430 Addressing Wait for command response G u r e 1 7 R e a d N e i g h b o r T a b l e C o m m a n d Command DefinitionsA d N e i g h b o r T a b l e V a N C E D N E T W O R K C O M M a N D S G u r e 1 9 R e a d R o u t e T a b l e C o m m a n d A d R o u t e T a b l eG u r e 2 0 R e a d R o u t e T a b l e R e s p o n s e G u r e 2 1 P e r f o r m S c a n C o m m a n d R f o r m S c a nIf Scan Type = 0x00 Byte 8 Channel Number Byte 9 Energy G u r e 2 2 P e r f o r m S c a n R e s p o n s eG u r e 2 3 R e a d R a d i o T a b l e C o m m a n d A d R a d i o T a b l eG u r e 2 4 R e a d R a d i o T a b l e R e s p o n s e G u r e 2 5 Z B 2 4 3 0 M e c h a n i c a l D r a w i n g Dimensions2 4 3 0 M E C H a N I C a L O D U C T P a R T N U M B E R S Ordering InformationE N C Y I D E N T I F I C a T I O N N U M B E R S Compliancy InformationP R O V E D a N T E N N a L I S T B l e 1 1 Z B 2 4 3 0 a p p r o v e d a n t e n n a L i s tContains FCC ID KQL-ZB2430-100 / KQL-ZB2430D M E Q U I P M E N T L a B E L I N G R E Q U I R E M E N T SM P L I a N C Y I N F or M a T I O N

ZB2430 specifications

The AeroComm ZB2430 is a highly regarded wireless module optimized for Zigbee applications, positioning itself as an ideal solution for connecting devices within the Internet of Things (IoT) ecosystem. With its robust features, advanced technologies, and impressive characteristics, the ZB2430 stands out in the crowded market of low-power, low-data-rate communication devices.

One of the primary features of the AeroComm ZB2430 is its superior range and reliability. Designed to operate in the 2.4 GHz ISM band, the ZB2430 boasts a communication range of up to 1,200 feet line of sight in open environments. This enables seamless connectivity for devices across extensive areas, making it suitable for applications such as remote monitoring and smart home systems. The ZB2430 also employs advanced error correction and data packet acknowledgment techniques, ensuring that data is transmitted accurately and reliably, even in challenging conditions.

Another significant characteristic of the ZB2430 is its low power consumption. Designed for energy efficiency, this module allows devices to operate on battery power for extended periods, which is critical for applications like sensor networks and portable devices. With power-saving modes that can further extend battery life, the ZB2430 is ideal for applications where minimizing energy use is essential.

The ZB2430 also supports a variety of communication protocols, including point-to-point and mesh networking capabilities. The mesh networking feature allows devices to communicate with each other even when they are not within direct range, creating a highly scalable and resilient network. This is particularly beneficial in industrial automation and smart city applications, where reliable communication is paramount.

In terms of integration, the AeroComm ZB2430 is designed with ease of use in mind. It comes in a small form factor that can be easily incorporated into various devices, and it features a simple interface for developers. With its comprehensive documentation and support, developers can quickly implement and deploy Zigbee solutions.

In summary, the AeroComm ZB2430 is a powerful wireless module that excels in providing reliable, low-power, and scalable communication solutions for IoT applications. Its impressive range, energy efficiency, and support for mesh networking make it an attractive choice for developers looking to create innovative and robust wireless systems. Whether in home automation, industrial control, or smart city initiatives, the ZB2430 is poised to play a key role in the future of connected devices.
Top Page Image Contents