Safety Instructions
IMPORTANT SAFETY INSTRUCTIONS
To reduce the risk of fire, electric shock and /or injury, always follow these
basic safety precautions when using your cordless telephone equipment.
1.Read and understand all instructions.
2.Follow all warnings and instructions marked on the telephone.
3.Do not use this telephone near a bathtub, kitchen sink, wash bowl, laundry tub, in a wet basement, near a swimming pool, or anywhere else where there is water.
4.Avoid using a telephone(other than a cordless type) during an electrical storm.There may be a remote risk of electric shock from lighting.
5.Do not use the telephone to report a gas leak in the vicinity of the leak.
6.Use only the power cord and BATTERY PACK indicated in the Owner's Manual. Do not dispose of the BATTERY PACK in a fire .The BATTERY PACK may explode . Check with local codes for possible special disposal instructions.
7.Unplug this telephone from the wall outlet before cleaning or replacing the BATTERY PACK. Do not use liquid cleaners or aerosol cleaners on the telephone. Use a damp cloth for cleaning.
8.Place this telephone on a stable surface. Serious damage and/or injury may result if the telephone falls.
9.Do not cover the slots and openings on this telephone. This telephone should never be placed near or over a radiator or heat register. This telephone should not be placed in a
10.Operate this telephone using the electrical voltage as stated on the BASE UNIT or in the Owner's Manual .If you are not sure of the voltage in your home , consult your dealer or local power company.
11.Do not place anything on the power cord. Install the telephone where no one will step or trip on the cord.
12.Do not overload wall outlets or extension cords as this can increase the risk of fire or electric shock.
13.Never push any objects through the slots in the telephone. They could touch dang- erous voltage points or short out parts that could result in a risk of fire or electric shock. Never spill liquid of any kind on the telephone.
14.To reduce the risk of electric shock, do not take this telephone apart. If service or repair work is required on this telephone, take it to a qualified service representative. Opening or removing covers may expose you to dangerous voltage or other risks. Incorrect reassembly can cause electric shock when the appliance is subsequently used.
15.Unplug this telephone from the wall outlet and consult a qualified service representa- tive in any of the following situations:
A.When the power supply cord is frayed or damaged.
B.If liquid has been spilled into the telephone.
C.If the telephone has been exposed to rain or water.
D.If the telephone does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions. Improper adjustment may require extensive work by a qualified technician to restore the telephone to normal operation.
Caller ID System Operation
TELEPHONE KEYPAD Characters
The TELEPHONE KEYPAD 
button are used to enter characters when
entering names. You can enter names in the UPPER CASE or LOWER CASE letters.
Press the appropriate TELEPHONE KEYPAD button to get the following characters.
KEYPAD | CHARACTERS | |
BUTTONS | ||
| ||
1 | SPACE1 &' ( ). | |
|
| |
2 | ABCabc2 | |
|
| |
3 | DEFdef3 | |
4 | GHIghi4 | |
|
| |
5 | JKLjkl5 | |
|
| |
6 | MNOmno6 | |
7 | PQRSpqrs7 | |
8 | TUVtuv8 | |
9 | WXYZwxyz9 | |
* | * | |
0 | 0 | |
# | # |
EXAMPLE:
If you want to enter the character "Abc" on the HANDSET LCD Screen.
1.Press the DIR button.
2.Press the EDIT /EDIT Button.
3.Press the TELEPHONE KEYPAD 
button,"A" will be displayed. The cursor will automatically move to the next character after 2 seconds.
4.Press the TELEPHONE KEYPAD 
button for 5 times to display"b".
5.Press the TELEPHONE KEYPAD 
button for 6 times to display"c"
The cursor will automatically move to the next character within 2 seconds after entering
the first character. Press the SHIFT RIGHT
button to produce a space. If you want to change any character, you can go back to the incorrect character by pressing the
SHIFT LEFT 
button. To delete the character inside the cursor, press the DEL /SCAN button.
3 | 24 |