Battery Cautionary Instructions

BATTERIES: CAUTION

To reduce the risk of fire or injury to persons, read and follow these instructions:

BE-3872 PARTS CHECKLIST

•For the cordless handset, use only 3.6V 400mAh Nickel-Cadmium (Ni-Cd), cordless telephone battery pack, 35BAT (included).

•Do not dispose of the batteries in a fire. The cells may explode. Check with local codes for possible special disposal instructions.

•Do not open or mutilate the batteries. Released electrolyte is corrosive and may cause damage to the eyes or skin. It may be toxic if swallowed.

•Exercise care in handling batteries in order not to short the battery with conducting materials such as rings, bracelets, and keys. The battery or conductor may overheat and cause burns.

•Do not attempt to rejuvenate the batteries identified for use with this product by heating them. Sudden release of the battery electrolyte may occur causing burns or irritation to eyes or skin.

•When inserting batteries into this product, the proper polarity or direction must be observed. Reverse insertion of batteries can cause charging, and that may result in leakage or explosion.

•Remove the batteries from this product if the product will not be used for a long period of time (several months or more) since during this time the battery could leak in the product.

•Do not store this product, or the batteries identified for use with this product, in high temperature areas. Batteries that are stored in a freezer or refrigerator for the purpose of extending shelf life should be protected from condensation during storage and defrosting.

Batteries should be stabilized at room temperature prior to use after cold storage.

The EPA certified RBRC® Battery Recycling Seal on the nickel-cadmium (Ni-Cd) battery indicates Aastra Telecom is voluntarily participating in an industry program to collect and recycle these batteries at the end of their useful life, when taken out of service in the United States or Canada.

The RBRC® program provides a convenient alternative to placing used Ni-Cd batteries into the trash or the municipal waste stream, which may be illegal in your area. Please call 1-800-8-BATTERY for information on

Ni-Cd battery recycling and disposal bans/restrictions in your area.

Aastra Telecom's involvement in this program is part of our commitment to preserving our environment and conserving our natural resources.

2.4GHz

In Use/

Low Batt.

MuteMEM

1. Handset

3. AC power adapter	4. 10-number
	memory card

QUICK START GUIDE

BE-3872

SETTING UP THE BASE

1.Install a 9V backup battery into the battery compartment, located on the base bottom.

2. Connect the telephone line cord to the "LINE" jack and to a telephone outlet.

3. Connect the AC power adapter to the 9V DC jack and to an AC outlet. Wait 15 seconds for the answering system to reset before using the base.

Note: Use only the supplied AC power adapter. Connect the AC power adapter to a continuous power supply.

INSTALL THE BATTERY

1. Slide open the battery compartment door on the bottom of the handset.

2. Insert the battery into the battery compartment and then plug the battery connector into the 2-pin connector located just inside the battery compartment.

3. Close the battery compartment door and place the handset on the base unit cradle. You will hear a tone and the CHARGE LED on the base will illuminate.

4. IMPORTANT: Charge the battery pack for at least 12 hours before using the handset the first time.

DAY AND TIME SETTING ON THE ANSWERING MACHINE

1. Press and hold [Time Set] for three seconds until “Monday” is heard.

2. Press the 7 /Repeat or 8 /Skip key to select the current day of the week. Press [Time Set] to store that information. “12 AM” will be announced.

3. Press 7 /Repeat or 8 /Skip to select the current hour (1AM through 12AM or 1PM through 12PM). Press [Time Set]. “00” will be announced.

4.Press 7 /Repeat or 8 /Skip as many times necessary to set the current minutes (01 through 59). Press [Time Set] again. The information will be stored and the new day and time will be announced.

CHANGING THE ANSWER MODE

There are three answering modes: Answer On, Answer Only, or Answer Off.

Turning the Answering System On/Off: When the answering machine is set off, the caller will not hear an announcement and will not be able to leave a message.

1. Press the [ANS On/Off] key to turn the answering machine on or off. The system will announce the current on/off status of the answering machine.

Choosing between Answer On and Answer Only: Make sure that the answering machine is on. Locate the ANS ONLY On/Off switch on the base bottom.

If the ANS ONLY switch is set to “Off,” the BE-3872 will play your announcement, and then allow the caller to leave a message.

If the ANS ONLY switch is set to “On,” the BE-3872 will play your answer-only announce- ment, and then disconnect the call. The caller is unable to leave any messages.

6. Quick start card

7. Ni-Cd battery pack

2.Base

5. 7-foot line

cord for desk use

8. Belt-Clip

1.Dial the answering machine phone number.

2.Press *, and then enter the two-digit remote code.

3.If you entered the correct code, the phone will announce the number of messages and begin playing the voice help menu.

4.Once the voice help menu begins, enter your commands.

5.When finished, hang up.

Write 2-digit remote code in boxes

9.Remote Access Card