SpectraLink E340, I640, h340 Certifying the NetLink Wireless Telephones, Conducting a Site Survey

Page 48

SpectraLink Corporation

Configuration and Administration—NetLink e340/i640 Wireless Telephone

 

Mitel Networks 3300 and SX-200 ICP and 5220 IP Phone emulation

10. Certifying the NetLink Wireless Telephones

Prior to determining that an installation is complete, test the handsets following the sequence given in the previous Testing a NetLink Wireless Telephone section and conduct a site survey mode test according to the directions given in the previous Diagnostic Tools section. Note any areas where coverage is conflicting or inadequate. Note any system difficulties and work with your wireless LAN and/or LAN system administrator to determine the cause and possible remedy. See the section NetLink Wireless Telephone Problems for clues to possible sources of difficulties. If any adjustments are made to the system, re-test the device in the same vicinity to determine if the difficulty is resolved.

The installer should not leave the site before performing installation verification.

These tests must be performed in typical operating conditions, especially if heavy loads occur. Testing sequence and procedure is different for every installation. Generally, you should organize the test according to area and volume, placing numerous calls to others who can listen while you perform coverage tests. Note any areas with excessive static or clarity problems and report it to a SpectraLink service engineer.

The coverage test will also require you to put the handset in Site Survey mode and walk the entire coverage area to verify all access points.

10.1 Conducting a Site Survey

Conduct a Site Survey of the installation, by walking the site looking for interfering

802.11systems, adequate coverage and channel assignment, and correct AP configuration.

1.Referring to section 6.1 Run Site Survey, put a handset into Site Survey in the Any/Smry ESSID mode. Walk throughout the site checking for any expected APs or other ESSIDs.

2.Then, walk the site again, in MyID/Smry ESSID mode, this time checking that every location has adequate coverage (there should be at least one AP stronger than -70dBm in all areas) and has good channel allocation (at any point, the strongest AP shown should be on a different channel than the next best choice).

3.Finally, use the single AP (MyID/Detl) display to check each AP, to ensure it is configured for the proper data rates, beacon interval, 802.11 options enabled, QoS method, and security method.

4.Make any necessary adjustments to AP locations and configurations and repeat steps 1-3 until the Site Survey shows adequate coverage and correct configuration at every location.

The installation is not complete until these certification steps have been performed. Do not hand out handsets at a site that has not been certified.

PN: 72-1084-02-E.doc

Page 48

Page 47 Page 49
Image 48
Page 47 Page 49
Contents NetLink e340/h340/i640 Wireless Telephone Configuration and AdministrationMitel Networks 3300 and SX-200 ICP Trademark Information Table of Contents About This Document Referenced DocumentsCustomer Support Hotline Icons and ConventionsNetLink e340/h340/i640 Wireless Telephone Overview QoS and SecurityQuick Start Guide System Diagram Mitel Networks IP telephony server architecture exampleSystem Components SpectraLink Corporation NetLink Wireless Telephone SpecificationsWPA2-PSK DHCP, TftpDisplay Audio Features Ringing and TonesStartup Sequence Icon Icons shown in bold turns off whenEXT Handset Modes Standby on-hookPredial Active off-hookNetLink Wireless Telephone Displays Status display areaLine display Menu displayNetLink Wireless Telephone Configuration Admin MenuOpening the Admin Menu Entering and editing Admin menu options Alphanumeric String EntrySelect button End Call keyAdmin menu Admin Menu 2nd Level 3rd Level Items 4th Level 5th LevelESS ID WEPAdmin Menu 2nd Level 3rd Level 4th Level Transmit Power Maximum 50 mW † 30 mW †Phone Config License Option Clear PIN NumberAdmin Password Network Config IP AddressesPush-to-talk Essid Security Transmit Power Regulatory DomainDiagnostics Run Site Survey Diagnostics ModeSyslog Mode Restore DefaultsUser-defined Preferences Standby menuStandby menu item Nd Level Rd Level Th Level PBX4th Level Standby menu item 2nd Level 3rd Level Telephone Ring Auxiliary Ring OK Up Phone Options System Info Channel Enable/Disable Audio Volume Tone V olume OK Up Configuration Process License ManagementRequirements SpectraLink Corporation Voice Messaging Access Mitel Networks VoIP Integration FactorsCODECs Option MeaningSpectraLink Corporation Feature Programming Feature Assignment 5220 key FeatureFCN + Feature Access Feature ListLine Appearances Superkey Hot DeskingResiliency Paging Testing a Handset Call keyDiagnostic Tools Run Site Survey7 b c Diagnostics Mode Solving Coverage IssuesScreen M m m Screen Syslog Mode Message type Errors Events FullMAC AP MACCertifying the NetLink Wireless Telephones Conducting a Site SurveySoftware Maintenance Upgrading NetLink Wireless TelephonesNormal Download Messages Message DescriptionDownload Failure or Recovery Messages Troubleshooting NetLink Wireless Telephone Problems Access Point ProblemsConfiguration Problems NetLink Wireless Telephone Status Messages Message Description ActionMessage Description Action Do not Power OFF PBX Configuration Note DhcpLAN Message Description Action Maintenance Index
Related manuals
Manual 1 pages 11.44 Kb Manual 1 pages 44.89 Kb

h340, I640, E340 specifications

The SpectraLink E340 is a robust and versatile mobile communication device designed specifically for business environments. Built to enhance productivity, this smartphone-like device boasts a range of features tailored to meet the needs of various industries, including healthcare, hospitality, and retail.

One of the standout characteristics of the E340 is its superior voice quality. Utilizing advanced Voice over IP (VoIP) technology, the device ensures crystal-clear audio, which is crucial for effective communication in fast-paced work settings. This high-quality voice capability minimizes misunderstandings, allowing employees to relay critical information quickly and efficiently.

The integrated Wi-Fi connectivity further amplifies the E340's functionality. By leveraging existing wireless networks, users can access communication tools and applications seamlessly, fostering real-time collaboration among team members. The device is also equipped with Bluetooth technology, offering compatibility with a range of accessories such as headsets, which enhances usability and convenience.

Durability is another defining feature of the SpectraLink E340. It is designed to withstand the rigors of demanding environments, with an IP54 rating that provides resistance against dust and water. This makes the E340 an ideal choice for industries such as healthcare, where devices are regularly exposed to spills and other contaminants.

Ergonomically designed, the E340 is lightweight and easy to handle, ensuring comfort during extended use. Its intuitive interface is tailored for efficient navigation, allowing users to access essential functions quickly without extensive training. The long-lasting battery life ensures that employees can remain connected throughout their shifts without the constant need for recharging.

The device supports a range of enterprise applications, allowing businesses to customize workflows and enhance operational efficiency. This adaptability makes it suitable for various use cases, from managing inventory in retail to providing instant communication in hospitals.

In summary, the SpectraLink E340 stands out in the market as a reliable communication tool that combines superior voice quality, Wi-Fi connectivity, durability, and ergonomic design. These features make it an excellent choice for organizations looking to enhance their mobile communication capabilities while ensuring that employees can stay connected and productive throughout their workday. Whether it’s onsite at a bustling hospital or within a dynamic retail environment, the E340 is engineered to facilitate seamless interactions and elevate workplace efficiency.
Top Page Image Contents