Topcom 4812 USB VOIP manual Topcom Butler 4812 USB VoIP

Page 20

Topcom Butler 4812 USB VoIP

Keep the Paging key on the base unit pressed for 10 seconds until The Line/Charge indicator on the base unit begins to blink rapidly. The Line/Charge indicator will blink rapidly for one minute. During this minute, the base unit is in subscribing mode and you must do the following to subscribe the handset:

•Press the Programming key .

•Press the Up or Down key repeatedly until ‘BASE SUB’ appears on the display.

•Press the Programming key .

•‘BASE _‘ appears on the display.

•Enter a number of the base unit you would like to subscribe the handset to (1-4). Use the number keypad.

•‘SEARCHING’ and the symbol appears on the display.

Each handset can be subscribed to 4 different DECT base units. Each base unit is assigned a number from 1 to 4 in the handset. When you subscribe a new handset, you can assign a base unit number. It is best to use ‘1’.

•The RFPI code (each base unit has a unique RFPI code) appears on the display and a signal sounds when the handset has found the base unit.

•Press the Programming key .

•‘PIN’ appears on the display.

•Enter the 4-digit PIN code of the base unit in (default PIN code is ‘0000’). Use the number keypad.

•Press the Programming key .

•The handset is subscribed to the base unit.

4.24 Subscribing Butler 4812 handset on another base (other brand/model)

Put the base in subscription mode (see manual of the base). If the base is in subscribing mode, you have to do the following to subscribe the handset:

•Press the Programming key .

•Press the Up or Down key repeatedly until ‘BASE SUB’ appears on the display.

•Press the Programming key .

•‘BASE _‘ appears on the display.

•Enter a number for the base unit to which you would like to subscribe the handset (1-4).

•Use the number keypad.

•‘SEARCHING’ and the symbol appear on the display.

•The RFPI code (each base unit has a unique RFPI code) appears on the display and a signal sounds once the base unit is found by the handset.

•Press the Programming key .

•‘PIN’ appears on the display.

•Enter the 4-digit PIN code of the base unit (default PIN code is ‘0000’). Use the number keypad.

•Press the Programming key .

•The handset is subscribed to the base unit.

20	Topcom Butler 4812 USB VoIP

Image 20

Contents Butler 4812 USB Voip Page Installation Voice mail indicatorKeys/LED Display LCD Handset operation Caller ID/CLIPTrouble shooting Technical characteristics Topcom warranty USB PC interface operationDisposal of the device environment Safety InstructionsCleaning Installation BaseCharger only in Twin, Triple or Quattro pack HandsetEys/LEDK HandsetDisplay LCD Setting the language Handset operationMaking Pstn Calls Receiving a Pstn Call An internal call calling another handsetReceiving an external call Receiving an internal callSetting the speaker volume Activate/deactivate handsfree functionTransferring a call to another handset Out of Range WarningCall Duration Indicator on the display Turning off the microphone mutePause key Locating a misplaced handset pagingUsing the alphanumeric handset keypad Phone BookAdding a number and a name to the Phone Book Looking up a number in the Phone BookSwitch the handset ON/OFF Switch the handset off The handset is turned onChanging a name or number in the Phone Book Deleting name and number from the Phone BookSetting the ring volume level on the handset Setting the ringer melody on the handsetSetting the ring volume and melody of the base Setting a ringer melody for internal callsSetting the base ring volume Setting a ringer melodyR key flash Locking the key padTurning key click ON/OFF Changing the PIN code You only need to subscribe the handset ifTopcom Butler 4812 USB VoIP Automatic selection Removing subscription of a handset to a base unitSelecting a base unit Barring outgoing calls Manual selectionDefault settings reset of the parameters Direct CallTo program the Direct Call number Turn the Direct Call function ON/OFFComplete reinitialisation of the telephone Setting the handset dialling modeCaller ID/CLIP Setting the date and time Call ListCalling a number from the Call List Storing a number from the Call List in the Phone BookDeleting numbers from the Call List Deleting one numberVoice mail indicator Installing the softwareUSB PC interface operation Minimum system requirementsGeneral PC call settings Setting the PC ringer melody and volume on the handsetPC Time Settings Skype interfaceGeneral comments Making Skype calls Receiving an incoming Skype callsRedial one of the last 5 numbers dialled Interworking Skype calls and normal Pstn calls PC Call ListSetting the Net status via handset Skype Voicemail accessTo have voicemail you need to have voicemail subscription Listen to your voicemail messagesMaking a PC call SJ-Phone/Net2Phone interfaceIncoming call MSN Messenger interface This section describes the operation under MSN MessengerTrouble shooting Symptom Possible cause SolutionTechnical characteristics Topcom warrantyWarranty period Warranty handlingWarranty exclusions Page Page Visit our website