Telephone Operation (Cont.)
Telephone Operation (Cont.)
When The "VOL/RING" button is pressed, the receiver volume will increase to maximum (level 3) and then back down and decrease to minimum (level 1) in a repeated cycle.
|
|
|
| DEL |
|
|
|
|
| S |
|
|
|
|
|
|
| CALL | TALK |
|
|
|
|
|
|
|
|
| H |
| |
|
|
|
| FLAS |
| ||
|
| MEM |
|
|
|
|
|
|
|
|
|
|
| 3DEF |
|
|
|
| 2ABC |
|
|
| |
|
| 1 |
|
|
| 6MNO | |
|
|
|
|
|
| ||
|
|
|
| 5JKL |
|
| |
|
| 4 | GHI |
|
|
| 9WXYZ |
| 0 OPER | # |
| 8 | TUV |
| |
| 7PQRS |
|
|
| |||
|
|
|
|
|
| # | |
REDIAL | CH | VOL/RING |
|
|
| OPER | ING |
|
| 0 |
| VOL/R | |||
|
|
|
|
|
| CH |
|
|
|
|
| IAL |
|
|
|
|
|
| RED |
|
|
| |
Ringer Control
If you do not want the handset and base to ring , set the RINGER switch on the back of the base unit to OFF and/or press the " VOL/RING " button on handset for 2 seconds to toggle the ringer to off. The LCD will show.
The handset and/or base unit will no longer ring when a call comes in.
| |||||
| BASE | HANDSET | BASE | HANDSET | |
| ON | OFF | ON | OFF | |
HANDSET | ON | ON | ON | ON | |
OFF | OFF | OFF | OFF | OFF | |
CRADLE | |||||
|
|
|
| ||
| OFF | ON | OFF | ON | |
| ON | OFF | ON | OFF | |
HANDSET | ON | ON | ON | OFF | |
ON | |||||
|
|
|
| ||
CRADLE | OFF | OFF | OFF | OFF | |
|
|
|
| ||
| OFF | ON | ON | OFF | |
Speakerphone Volume Control
Press the VOLUME control "
"or" 
" button on the base to adjust the speakerphone volume level.
| F |
|
|
|
|
| N/OF |
|
|
|
|
D | IO O |
|
|
|
|
|
|
|
|
| |
RA | FUNCTION |
|
|
|
|
E |
|
|
|
| |
N |
|
|
| /O | F |
|
|
|
|
| |
|
|
| IO | ON |
|
| R A | D |
|
| |
|
|
|
| ||
|
|
|
|
| |
|
|
|
|
| FUNCTION |
| E |
|
|
|
|
| N |
|
| ||
| T |
|
| ||
|
|
| E | R |
|
Page/Handset Locator
You can send a page signal from the base to the handset.
Press the "PAGE" button on the base once, and the handset will beep 3 times. Press and hold the "PAGE" button for 3 seconds, and the handset will beep for about 60 seconds. Press any button on the handset to stop the handset from beeping.
|
| E |
|
|
| PAG |
|
CHARGE |
| ALARM | SPEAKER |
SET | SNOOZE | 1 | 2 |
LCD/LED INDICATIONS (HANDSET)
LED | STATUS | INDICATIONS |
NEW | FLASHING | |
CALL |
| memory. |
LED |
|
|
| OFF | |
|
| already been reviewed. |
|
|
|
LCD DISPLAY | INDICATIONS |
BATTERY LOW | Handset battery power is low, and the |
| handset battery should be charged. |
PAGING | Base unit is paging handset. |
TALK | Handset is connected to line. |
LINE IN USE | Speakerphone active. |
|
|
Power failure protection/Battery Backup
If DC power failure occurs, or the power plug comes out of the wall, your unit will shut down until the power is restored.
When the power is restored, clock and alarm time and memory settings recorded before the power failure will be saved IF YOU HAVE INSTALLED A 9 VOLT BATTERY.
If your unit is not operating properly when the power is restored, proceed with a unit reset.
To Reset Unit
1.Unplug the DC adaptor from the power outlet.
2.Remove the 9 volt battery. Replace with a fresh 9 volt battery (see page 9).
3.Plug DC adaptor back into power outlet.
4.Set clock and alarm time, radio memory station (see page 21).
5.Remove the handset battery, wait 5 seconds, and then reinstall the handset battery. You need to follow the Caller ID setup procedure.
IMPORTANT
During a power outage, your unit will NOT work, even if a 9 volt battery is installed.
19 | 20 |