Telephone Operation (Cont.)
When the handset is not in the base, only a handset having the identical security code and operating on the same channel can access the base and use your phone line.
The handset display will show TALK. The base display will show LINE IN USE
Telephone Operation (Cont.)
Note:
If you experience difficulty with placing or receiving calls, lost security code may be the cause of the problem. When this occurs, the
5. To remove the belt clip from the |
back of the handset, use your fingernails |
to loosen one of the "arms" of the belt |
clip. The other "arm" of the belt clip |
will automatically release from the |
When the handset is in the base, no other handset, even those having the identical security code and operating on the same channel, can access the base and use your line.
Digital security coding will also eliminate the "false" ringing associated with cordless telephones not equipped with this feature.
40 Channel Operation
CALLS | DEL |
| TALK |
MEM | FLASH |
|
| DEL |
|
|
S |
|
|
|
|
CALL |
|
|
|
|
|
| TALK |
|
|
|
| FLASH |
| |
ME | M |
|
|
|
|
|
|
| |
|
|
| 3DEF |
|
|
| 2ABC |
|
|
| 1 |
| 6MNO | |
|
| 5 JKL |
|
|
| 4 | GHI |
| 9WXYZ |
|
|
| ||
|
| 8TUV |
| |
|
| RS |
|
|
|
| 7PQ |
| # |
|
|
| OPER | ING |
|
| 0 |
| VOL/R |
|
|
| CH |
|
|
| L |
|
|
|
| REDIA |
|
|
handset can no longer communicate with its base. The loss of the code can occur any of the following ways: the battery is drained and needs recharging; the DC adaptor is disconnected or a power loss has occurred; or anything that causes electrical interference, for example, multiple cordless telephones, baby monitors, televisions, VCR's etc. Reset the security code by placing the handset on the base for 10
handset. |
Note:
Your cordless telephone has 40 operating channels. The phone will automatically search and select the clearest channel when you pick up the handset and press the "TALK" button. If you hear noise or other interference during your conversation, you can manually select a clearer channel by pressing and releasing the channel control on the handset to switch to another spare channel. Your call will not be interrupted.
DEL |
S |
CALL |
LK |
3.After hearing a dial tone, dial the desired number.
4.If you misdial, simply press the "TALK" button, wait for a couple of seconds, and press the "TALK" button again for a new dial tone.
5.After your conversation is completed, press the "TALK" button once to disconnect the line, or return the handset to the base.
Receiving a Call Through the Handset
seconds, removing it from the base, then replacing it on the base for an additional 10 seconds.
The unit will beep and you can now make the call. If that does not work, make sure DC adaptor is connected. If necesssary, unplug the DC adaptor from the power source. Disconnect the battery for 5 seconds and then reconnect. Place the handset on the base and then replug the DC adaptor (see Troubleshooting). Let stand 2 minutes before use.
http://www.swbfreedomphone.com, or your local retailer.
| TA |
| SH |
|
|
|
| FLA |
|
| |
MEM |
|
|
|
|
|
|
|
| 3DEF |
|
|
|
| 2ABC |
|
|
|
1 |
|
| 6MNO |
| |
|
|
|
| ||
|
| 5JKL |
|
|
|
4 | GHI |
|
| 9WXYZ |
|
|
|
|
| ||
|
| 8TUV |
|
| |
| 7PQRS |
| # |
| |
|
| 0 | OPER | VOL | /RING |
|
|
|
| ||
|
|
| CH |
|
|
|
| IAL |
|
|
|
|
| RED |
|
|
|
Note:
You must be within maximum range to change channel. If you come close to being out of range, you may lose the call. If this occurs, place the handset back into the base for ten seconds to reset the security code and then make the call again.
Making a Call
1.Lift the handset and press the "TALK" Button to be connected to the phone line.
When the Phone Rings
1.IF THE HANDSET IS OUT OF THE CRADLE, press any key on the handset.
2.IF THE HANDSET IS IN THE CRADLE, lift the handset. DO NOT press the "TALK" button, as you will be connected automatically.
Receiving Call Through the Base
Press the "SPEAKER" button on the base unit. You can speak through the microphone, without lifting the handset or press the "TALK" Button on the handset. H/S display will show "LINE IN USE". Press the "SPEAKER" button again to terminate a call.
Headset Jack
You can connect a headset (not included) for
1.Insert the headset plug (must be 3/32 inch/ 2.5mm type) into the headset jack on the side of the handset.
2.Attach the belt clip to the back of the handset. Make sure the "arms" of the belt clip snap securely into the notches on the side of the handset. You can now attach the handset/ belt clip to the desired location on your clothing.
3.Adjust the headset microphone to a comfortable position, placing it near your mouth.
4.Press the "TALK" button to make or receive a call.
Out of Range
If you experience static while using the telephone, move closer to the base or change the channel by pressing the "CH" button on handset.
| DEL |
|
|
| |
CALLS |
|
|
|
|
|
TALK |
|
| H |
|
|
| FLAS |
|
| ||
MEM |
|
| 3DEF |
|
|
|
|
|
|
| |
2ABC |
|
|
|
| |
1 |
|
| 6MNO |
| |
| 5JKL |
|
|
|
|
4 GHI |
|
|
| 9WXYZ |
|
| 8 | TUV |
|
| |
S |
|
|
|
| |
7PQR |
|
|
| # |
|
|
| 0 | OPER | VOL/R | ING |
|
|
|
| ||
|
|
| CH |
|
|
REDIAL |
|
|
|
| |
13 | 14 |