OP Erating I N S T R U C T I O N S, Base Ringer

OP - ER'ATING I N S T R U C T I O N S

O P E R A T I N G I N S T R U C T I O N S

Press 1 , 2 3, or 4 on the Handset to select	MEMORY DIALING
a ringer type. The Handset will emit the cor-	MEMORY DIALING
a ringer type. The Handset will emit the cor-		The 917ADXcordless phone can store up
responding ringer tone.		The 917ADXcordless phone can store up
responding ringer tone.	to10 frequently dialed numbers in memory.
	to10 frequently dialed numbers in memory.
Press OFF on the Handset to exit pro-		Memory Dial numbers must be stored us-
		Memory Dial numbers must be stored us-
yamming.	ing the Handset, but can be recalled from ei-
	ing the Handset, but can be recalled from ei-
	ther the Base Unit or the Handset.

WRNlNG OFF THE HANDSET RINGER	TO STORE A NUMBER INTO MEMORY
The Handset must	The Handset must be OFF
)e OFF	Press PRGIPRV on the Handset
IPress PRGIPRV on		.Press	the Memory
he Handset		Location key where the
		phone number will be
IPress # or 'key on
	TO PROGRAM	stored (0-9)
he Handset	THE RING TYPE
		.Dial	the number you
IPress 5 to turn off
	MEMORY DIALING	want to store. The num-
he ringer
		ber can be up to 16
IPress OFF key to
		digits long
!xit		.Press	MEM on the

		Handset to complete
		programming
		fI. programming has
		been successful,a
BASE RINGER		happy tone will be
CONTROL		generated.

Press PHONE (on the Handset) or SPKR (on the Base Unit) to get a dial tone

Press MEM and the Memory Location key

(0-9)

For example, to dial the number you as- signed to key '8',you would press PHONE, MEM, 8 (on the Handset), or SPKR, MEM, 8 (on the Base Unit).

TO CHANGE OR REPLACE A STORED NUMBER

You can change or replace a stored phone number by storing a new number in its place.

To insert a pause while programming a Memory Dial number, do the following on the Handset:

Press PRGIPRV on the Handset

Press the Memory Location key where the

phone number will be stored (0-9)

Dial the number you want to store, press-

ing HOLD at the appropriate point (to insert a

2 second pause). The number can be up to

16 digits long. Each press of HOLD is treated

as stored digit.

For longer pauses, press HOLD two or

more times. Each press makes the pause 2

seconds longer and is treated as a stored

digit.

Press MEM on the Handset to complete

programming.

For example, if your phone is connected to a PBX, you can store the PBX access num- ber and a pause before the phone number. To store 9-PAUSE-555-1234,in Memory Lo- cation 8, you would:

Press PRWPRV

IThis control switch is located on the right and edge of Base Unit.

1Select HIGH, LOW or OFF setting.

CHECKING:HECKING.THE HANDSET RINGER '

( To check the ringer type which is currently rogrammed, do the following:

1 Handset must be OFF

IPress PRWPRV on the Handset 1 Press # key on the Handset

1 Press 0 on the Handset. The phone will ring once to show ringer selected.

1 Press OFF key to exit

If programming was unsuccessful, a sad tone is generated.

If the phone is left unattended in program mode for longer than 30 seconds, it will gen- erate a sad tone and automatically exit pro- gram mode.

Write down the phone number you as- signed to each Memory Location key on the directory card in the Base Unit cradle.

TO DIAL A NUMBER FROM MEMORY

You can Memory Dial from either the Handset or the Base Unit .

See TO STORE A NUMBER INTO MEMORY.

TO ERASE STORED NUMBER

FROM MEMORY

The Handset must be OFF.

Press PRGIPRV on the Handset.

Press the Memory Location of the phone number to be erased.

Press MEM on the handset to complete programming.

STORING PAUSES IN MEMORY

Press 8