Avaya 8400-SES manual Configure SIP Trunk, Signaling Group, Trunk Group

Page 10

Direct IP-IP Audio Connections – Set to y, since Media Shuffling is enabled during the compliance test

 

add signaling-group 201

 

 

 

Page

1 of 1

 

 

 

 

 

 

SIGNALING GROUP

 

 

 

 

Group Number: 201

 

 

 

 

 

 

 

 

 

 

Group Type: sip

 

 

 

 

 

 

 

 

 

Transport Method: tls

 

 

 

 

IMS Enabled? n

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Near-end Node Name: CLAN

 

 

 

Far-end Node Name: SES

 

 

 

 

 

Near-end Listen Port: 5061

 

Far-end Listen Port: 5061

 

 

 

 

 

 

 

 

 

Far-end Network Region: 1

 

 

 

 

 

Far-end Domain: avaya.com

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Bypass If IP Threshold Exceeded? n

 

 

Incoming Dialog Loopbacks: eliminate

 

 

RFC 3389 Comfort Noise? n

 

 

 

DTMF over IP: rtp-payload

 

 

Direct IP-IP Audio Connections? y

 

 

 

Session Establishment Timer(min): 3

 

 

IP Audio Hairpinning? n

 

 

 

Enable Layer 3 Test? n

 

 

Direct IP-IP Early Media? n

 

 

H.323 Station Outgoing Direct Media? n

 

 

Alternate Route Timer(sec): 6

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

5.6. Configure SIP Trunk

This section describes the steps for administering a trunk group in Communication Manager for communication between Communication Manager and SIP Enablement Services. Enter the add trunk-group <t> command, where t is an unallocated trunk group and configure the following:

Group Type – Set the Group Type field to sip.

Group Name – Enter a descriptive name.

TAC (Trunk Access Code) – Set to any available trunk access code.

Signaling Group – Set to the Group Number field value configured in Section 5.5.

Number of Members – Allowed value is between 0 and 255. Set to a value large enough to accommodate the number of SIP telephone extensions being used.

Note: Each SIP call between two SIP endpoints (whether internal or external) requires two SIP trunks for the duration of the call. The license file installed on the system controls the maximum permitted.

 

add trunk-group 201

 

 

 

 

Page

1 of 21

 

 

 

 

 

 

TRUNK GROUP

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Group Number:

201

 

 

Group Type: sip

 

 

CDR Reports: y

 

 

 

Group Name: To SES

 

 

COR: 1

 

 

TN: 1

TAC: 116

 

 

 

 

Direction: two-way

Outgoing Display? y

 

 

 

 

 

 

 

 

 

Dial Access? n

 

Night Service:

 

 

 

 

 

 

Queue Length: 0

 

 

 

 

 

 

 

 

 

 

 

Service Type: tie

 

Auth Code? n

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Signaling Group: 201

 

 

 

 

 

 

 

 

 

 

Number of Members: 10

 

 

CRK; Reviewed:

Solution & Interoperability Test Lab Application Notes

10 of 21

SPOC 7/1/2011

©2011 Avaya Inc. All Rights Reserved.

Polycom8400-SES

Image 10
Contents Abstract Introduction Interoperability Compliance TestingGeneral Test Approach and Test Results Test Results Reference ConfigurationSupport Test Configuration of SpectraLink 8400 Series Equipment and Software Validated Configure the Avaya Aura Communication ManagerEquipment Software/Firmware Capacity Verification Optional FeaturesOptional Features IP Port Capacities Used Used## SET ENABLEG711U IP Codec Set## SET G726PAYLOADTYPE Configure IP Network RegionSET ENABLEG722 ## SET DtmfpayloadtypeConfigure IP Node Name Configure SIP SignalingSignaling Group Configure SIP TrunkTrunk Group ∙ Type Set to 9630SIP Configure SIP Endpoint∙ Config Set Set to ∙ Application Set to OPSExtensions to Call Which Activate Features by Name Configure SIP Enablement Services Configure SIP Enablement Services Server PropertiesPage Configure Communication Manager Server Interface ∙ Pattern Click on the Add buttonConfigure Users Page Configure SpectraLink 8400 Series Conclusion PhoneconfigVerification Steps Additional ReferencesAvaya Inc. All Rights Reserved