Telos Zephyr Xport manual Audio Inputs, Audio Outputs

Page 28

ZEPHYR XPORT USER’S GUIDE

3.2.1 Audio Inputs

The Xport mixer has two analog audio inputs as follows:

MIC INPUT

This XLR female input will accept microphones with nominal output levels from - 53 to - 43 dBu. A Phantom Power source of 12 volts at 10 milliamps will power most Condenser microphones. Enabling phantom power is covered in section 6.3.

The microphone input gain is set by a menu option called Mic Gain.

NOTE: Microphones that require a voltage greater than 12 volts will require an external power supply.

LINE INPUT

This ¼" balanced (TRS) connector accepts line level inputs with nominal levels of +4 to - 9 dBu. Maximum input level (clip point) is 20 dBu.

When using unbalanced sources we recommend using pin 2 and 3 to connect the signal and ground, respectively. By leaving pin 1 unconnected, you will prevent ground loops.

The AUX INTERFACE connector can also be used to provide an additional input to the local monitor mix. See below.

AUDIO PROCESSING

The output of the mixer is fed to the DSP section through an analog- to- digital converter. It then passes through an Omnia ® audio processor section and from there feeds the codec section. A menu option called Process allows the processor to be set for Voice, Music, or Off.

3.2.2 Audio Outputs

The following audio outputs are provided (The AUX INTERFACE connector also has an output, see below):

HEADPHONE

This ¼" output provides a mix of the send audio (from the Mic and Line inputs) and the audio received from the far end site. The ratio of these is controlled using the Mix control on the front panel. The headphone volume is controlled using the front panel control. While the audio is mono, this connector is designed to drive both sides of standard stereo headphones.

MONITOR MIX OUT

This ¼" balanced output contains the same audio as on the headphone jack (see above) at a nominal level of +4 dBu (20 dBu clip point).

When used to feed an unbalanced destination, we recommend that you use Tip and Ring for the signal and ground respectively, and leave the sleeve unconnected. By leaving the sleeve unconnected, you will prevent ground loops.

18CHAPTER 3 - THE DETAILS

Page 27 Page 29
Image 28
Page 27 Page 29
Contents Zephyr Xport Xports Front Panel Mixer SectionZephyr Xport Customer Service Fax +1Important Note Test Lines Introducing the Xport VI Introducing the Xport Table of Contents Specifications & Warranty Looking for Information? Tell me more about the box Getting Oriented Quick StartConnecting the Audio Inputs/Outputs Connecting to the Telephone LineWhat you need before you start… Success, Step-by-StepBasic Configuration Powering UpSetting the Country Time to turn on the XportMixer Adjustments HeadphonesPlacing Your First Call, to Telos MicrophoneWhat’s Next? Snd RcvWhat have we here? AccessoriesFront panel Default Display Pots Connection Status see .1.2 for Isdn Connection statusExample 1 Selecting a setting from a list country MenusMore on the Numeric Keypad Entering Alphabetic Characters Example 2 Entering a numeric entry i.e. entering a prefixDial menu Frequently Used Menus AUTO, DIAL, & DropXport Phone Rear panelZephyr Isdn Support Telephone Connections DetailsPots Isdn Interface Optional Interface only active if option 1701-00056 is presentAudio Connections & Mixer InputAudio Inputs Audio OutputsInterface Connector SetupsAUX Interface connector AUX Interface Input ring & sleeveDial Setups Activating a Dial Setup Step by StepLocation Setups Activating a Location Setup Step by Step Creating Location Setups Set by StepEditing Location Setups Isdn Configuration Menu Xports Isdn interfaceConnecting two Xports to the same Isdn circuit Sharing Isdn in the USA & CanadaCell Phone Interfacing the Aux Audio Interface Sharing Isdn worldwideConnecting the Cell Phone to the Xport InstallationFeeding the Xport from a computer over Ethernet Telos Soundcard EmulatorConfiguring Windows Sounds and Media Changing configurationSelecting a Playback Device Remote Control Changing the playback volumeFrequently Asked Questions Is Xport a Pots codec?Can I share an Isdn line between two Xports? What happens when the line is very bad?What about international calls? So what is the Aux Interface connector for? Tell me more about the Ethernet?Where can I get answers to my technical questions? Anything better possible with mobile phones?What to do if… Why does my Isdn Xport take so long to boot up?How can I tell if my Xport has the Isdn option? Can’t find the Isdn setup menu Is the line shared between the Xport and any other device?Can’t place a call using Isdn in Zephyr mode Can the Xport place a call to a Telephone?Can’t place or receive calls using Isdn Technical & Installation Information Ventilation and ambient temperatureEnvironmental Considerations AC mains requirementsInstalling the Isdn option Echnical & Installation Ifnormation Enabling Phantom Power Specifications & Warranty Delay round tripFemale Line Input balanced ¼ TRSHeadphone Output Monitor MIX OUT Floating Balanced ¼ TRS Mix POT set to SendZephyr Xport Limited Warranty Ordering Isdn ReferencesTechnology Articles White Papers Xports Rear Panel Output

Zephyr Xport specifications

The Telos Zephyr Xport is a cutting-edge audio-over-IP codec that seamlessly revolutionizes the way audio is transmitted over networks. Renowned for its high-quality sound, this powerful codec is designed for both radio broadcast applications and professional audio environments, enabling efficient, reliable, and high-fidelity audio transport over IP networks.

One of the main features of the Zephyr Xport is its ability to handle multiple audio formats, including PCM, AAC, and MP3, which provides users with flexibility depending on their specific needs. Its ability to encode and decode audio ensures that broadcasters can deliver outstanding quality both on the air and in streaming applications.

The technology behind the Zephyr Xport includes advanced algorithms that minimize latency, making it ideal for live broadcasts where real-time transmission is crucial. With a low latency rate, users can enjoy audio transmission that is nearly instantaneous, a defining feature for any live event or remote broadcasting situation.

Another standout characteristic of the Zephyr Xport is its support for multiple network protocols, including RTP/RTCP, SIP, and POTS. This versatility allows integration with a wide range of existing equipment and infrastructures, facilitating easy implementation in various settings. Additionally, the codec boasts robust error correction and adaptive bitrate control to ensure audio clarity even in fluctuating network conditions, reducing the chances of dropouts or interruptions.

The user-friendly interface of the Zephyr Xport features an intuitive LCD display, making it easy for operators to configure settings, monitor audio levels, and manage network connections. With built-in web access, users can make adjustments and control the unit remotely, providing added convenience for situations where operators are away from the hardware.

Moreover, the Zephyr Xport is designed for durability and reliability, constructed to endure the demands of a fast-paced broadcast environment. Its compact design makes it suitable for rack mounting or portable use, allowing broadcasters to take it on location without hassle.

In summary, the Telos Zephyr Xport combines advanced audio processing technologies with user-friendly features, making it an essential tool for modern broadcasters. Its high-quality audio performance, low latency communication, versatile protocol support, and ease of use exemplify the future of audio transmission in the ever-evolving landscape of digital broadcasting. As the industry continues to embrace IP-based solutions, the Zephyr Xport stands out as a vital asset for any professional audio application.
Top Page Image Contents