Telos Zephyr Xport manual Installing the Isdn option

Page 49

ZEPHYR XPORT USER’S GUIDE

Some failures are catastrophic failures, while some are due to the cumulative damage that can occur over the course of several years. For this reason, we recommend that in addition to AC (mains) power protection (see above), that a quality telephone line surge protector be employed at the back panel of the Zephyr Xport. The ground terminal of this device should be connected directly to the Zephyr Xport chassis, and the protector connected to the Xstream’s ISDN and/or POTS Interface jack with as short a cable as possible (under 8 inches). This approach is particularly well suited to situations where you expect nearby strikes, such as when you are located near a tower. See www.telos- systems.com for additional information on telephone line protection.

6.2 Installing the ISDN option

 

e

 

IMPORTANT!

WARNING!

DANGER!

 

 

w

 

 

 

Always disconnect AC (mains) power and Telephone Circuit(s) before

 

 

 

 

 

removing the Zephyr Xport’s cover.

 

 

 

 

 

 

Potentially lethal voltages are inside! Failure to observe the above

 

 

 

 

 

warning may result in electric shock, injury or even death!

 

 

 

 

 

Refer all servicing to qualified personnel.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

The Xport can be ordered with, or without, one of the ISDN options. The ISDN interface connectors will not be active if the associated option is not present. You check for the presence of this interface by looking in the About menu option. The two ISDN options are:

•Telos Part # 1701- 00056: for use in the USA & Canada. Allows operation with the ISDN "S" (4- wire) interface or the ISDN "U" (2- wire) interface in the USA and Canada.

•Telos Part # 1701- 00135: For sale worldwide: Supports the ISDN "S" interface.

To Install the ISDN option card, follow the steps below:

1.Disconnect the AC (mains) power cord and all telephone connections from the rear panel of the Xport.

2.Remove the rear bumper of the Xport by gently pulling at the top with your fingers (see photo)

3.Remove the 6 Phillips- head screws around the perimeter of the rear panel.

4.Grasp the rear panel and pull it partially out (see picture below).

5.Look at the bottom of the unit, and locate the green wire going to the power entry module. Disconnect this green wire by unplugging it from the power module. Pull the board out from the chassis.

CHAPTER 6 - TECHNICAL & INSTALLATION INFORMATION 39

Page 48 Page 50
Image 49
Page 48 Page 50
Contents Zephyr Xport Mixer Section Xports Front PanelZephyr Xport Fax +1 Customer ServiceImportant Note Test Lines Introducing the Xport VI Introducing the Xport Table of Contents Specifications & Warranty Looking for Information? Tell me more about the box Quick Start Getting OrientedConnecting to the Telephone Line Connecting the Audio Inputs/OutputsWhat you need before you start… Success, Step-by-StepPowering Up Basic ConfigurationSetting the Country Time to turn on the XportHeadphones Mixer AdjustmentsPlacing Your First Call, to Telos MicrophoneSnd Rcv What’s Next?What have we here? AccessoriesFront panel Pots Connection Status see .1.2 for Isdn Connection status Default DisplayMenus Example 1 Selecting a setting from a list countryExample 2 Entering a numeric entry i.e. entering a prefix More on the Numeric Keypad Entering Alphabetic CharactersDial menu Frequently Used Menus AUTO, DIAL, & DropXport Phone Rear panelZephyr Isdn Support Telephone Connections DetailsPots Interface only active if option 1701-00056 is present Isdn Interface OptionalInput Audio Connections & MixerAudio Outputs Audio InputsSetups Interface ConnectorAUX Interface connector AUX Interface Input ring & sleeveActivating a Dial Setup Step by Step Dial SetupsLocation Setups Creating Location Setups Set by Step Activating a Location Setup Step by StepEditing Location Setups Xports Isdn interface Isdn Configuration MenuSharing Isdn in the USA & Canada Connecting two Xports to the same Isdn circuitSharing Isdn worldwide Cell Phone Interfacing the Aux Audio InterfaceInstallation Connecting the Cell Phone to the XportFeeding the Xport from a computer over Ethernet Telos Soundcard EmulatorConfiguring Windows Sounds and Media Changing configurationSelecting a Playback Device Changing the playback volume Remote ControlIs Xport a Pots codec? Frequently Asked QuestionsCan I share an Isdn line between two Xports? What happens when the line is very bad?What about international calls? Tell me more about the Ethernet? So what is the Aux Interface connector for?Anything better possible with mobile phones? Where can I get answers to my technical questions?What to do if… Why does my Isdn Xport take so long to boot up?How can I tell if my Xport has the Isdn option? Is the line shared between the Xport and any other device? Can’t find the Isdn setup menuCan the Xport place a call to a Telephone? Can’t place a call using Isdn in Zephyr modeCan’t place or receive calls using Isdn Ventilation and ambient temperature Technical & Installation InformationEnvironmental Considerations AC mains requirementsInstalling the Isdn option Echnical & Installation Ifnormation Enabling Phantom Power Delay round trip Specifications & WarrantyFemale Line Input balanced ¼ TRSMonitor MIX OUT Floating Balanced ¼ TRS Mix POT set to Send Headphone OutputZephyr Xport Limited Warranty Ordering Isdn ReferencesTechnology Articles White Papers Output Xports Rear Panel

Zephyr Xport specifications

The Telos Zephyr Xport is a cutting-edge audio-over-IP codec that seamlessly revolutionizes the way audio is transmitted over networks. Renowned for its high-quality sound, this powerful codec is designed for both radio broadcast applications and professional audio environments, enabling efficient, reliable, and high-fidelity audio transport over IP networks.

One of the main features of the Zephyr Xport is its ability to handle multiple audio formats, including PCM, AAC, and MP3, which provides users with flexibility depending on their specific needs. Its ability to encode and decode audio ensures that broadcasters can deliver outstanding quality both on the air and in streaming applications.

The technology behind the Zephyr Xport includes advanced algorithms that minimize latency, making it ideal for live broadcasts where real-time transmission is crucial. With a low latency rate, users can enjoy audio transmission that is nearly instantaneous, a defining feature for any live event or remote broadcasting situation.

Another standout characteristic of the Zephyr Xport is its support for multiple network protocols, including RTP/RTCP, SIP, and POTS. This versatility allows integration with a wide range of existing equipment and infrastructures, facilitating easy implementation in various settings. Additionally, the codec boasts robust error correction and adaptive bitrate control to ensure audio clarity even in fluctuating network conditions, reducing the chances of dropouts or interruptions.

The user-friendly interface of the Zephyr Xport features an intuitive LCD display, making it easy for operators to configure settings, monitor audio levels, and manage network connections. With built-in web access, users can make adjustments and control the unit remotely, providing added convenience for situations where operators are away from the hardware.

Moreover, the Zephyr Xport is designed for durability and reliability, constructed to endure the demands of a fast-paced broadcast environment. Its compact design makes it suitable for rack mounting or portable use, allowing broadcasters to take it on location without hassle.

In summary, the Telos Zephyr Xport combines advanced audio processing technologies with user-friendly features, making it an essential tool for modern broadcasters. Its high-quality audio performance, low latency communication, versatile protocol support, and ease of use exemplify the future of audio transmission in the ever-evolving landscape of digital broadcasting. As the industry continues to embrace IP-based solutions, the Zephyr Xport stands out as a vital asset for any professional audio application.
Top Page Image Contents