Telos Zephyr Xport manual Introducing the Xport

Page 7

ZEPHYR XPORT USER’S GUIDE

e

WARNING:

ZEPHYR XPORT USES CONVECTION COOLING. DO NOT BLOCK THE VENTILATION OPENINGS IN THE TOP AND REAR OF THE UNIT.

FAILURE TO ALLOW PROPER VENTIUALATION COULD DAMAGE THE UNIT OR CREATE A FIRE HAZARD.

DO NOT PLACE THE UNIT ON A CARPET, BEDDING, OR OTHER MATERIALS THAT COULD INTERFERE WITH THE REAR PANEL VENTILATION OPENINGS.

DO NOT STACK MORE THAN 3 UNITS HIGH.

This symbol, wherever it appears, alerts you to the presence of uninsulated, dangerous voltage inside the enclosure – voltage which may be sufficient to constitute a risk of shock.

This symbol, wherever it appears, alerts you to important operating and maintenance instructions. Read the manual.

TO PREVENT RISKS OF

ELECTRIC SHOCK,

DISCONNECT POWER

CORD BEFORE SERVICING

USA CLASS A COMPUTING DEVICE INFORMATION TO USER. WARNING: This equipment generates, uses, and can radiate radio-frequency energy. If it is not installed and used as directed by this manual, it may cause interference to radio communication. This equipment complies with the limits for a Class A computing device, as specified by FCC Rules, Part 15, Subpart J, which are designed to provide reasonable protection against such interference when this type of equipment is operated in a commercial environment. Operation of this equipment in a residential area is likely to cause interference. If it does, the user will be required to eliminate the interference at the user’s expense. NOTE: Objectionable interference to TV or radio reception can occur if other devices are connected to this device without the use of shielded interconnect cables. FCC rules require the use of only shielded cables.

CANADA WARNING: “This digital apparatus does not exceed the Class A limits for radio noise emissions set out in the Radio Interference Regulations of the Canadian Department of Communications.” “Le present appareil numerique n’emet pas de bruits radioelectriques depassant les limites applicables aux appareils numeriques (de les Class A) prescrites dans le Reglement sur le brouillage radioelectrique edicte par le ministere des Communications du Canada.”

SAFETY CAUTION: “To reduce the risk of fire, use only N0. 26 AWG gauge Telecommunications line cord to connect between your Xport and the telephone circuit.”

CHAPTER 1 - INTRODUCING THE XPORT v

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Zephyr Xport Mixer Section Xports Front PanelZephyr Xport Fax +1 Customer ServiceImportant Note Test Lines Introducing the Xport VI Introducing the Xport Table of Contents Specifications & Warranty Looking for Information? Tell me more about the box Quick Start Getting OrientedSuccess, Step-by-Step Connecting the Audio Inputs/OutputsConnecting to the Telephone Line What you need before you start…Time to turn on the Xport Basic ConfigurationPowering Up Setting the CountryMicrophone Mixer AdjustmentsHeadphones Placing Your First Call, to TelosSnd Rcv What’s Next?What have we here? AccessoriesFront panel Pots Connection Status see .1.2 for Isdn Connection status Default DisplayMenus Example 1 Selecting a setting from a list countryExample 2 Entering a numeric entry i.e. entering a prefix More on the Numeric Keypad Entering Alphabetic CharactersDial menu Frequently Used Menus AUTO, DIAL, & DropXport Phone Rear panelZephyr Isdn Support Telephone Connections DetailsPots Interface only active if option 1701-00056 is present Isdn Interface OptionalInput Audio Connections & MixerAudio Outputs Audio InputsAUX Interface Input ring & sleeve Interface ConnectorSetups AUX Interface connectorActivating a Dial Setup Step by Step Dial SetupsLocation Setups Creating Location Setups Set by Step Activating a Location Setup Step by StepEditing Location Setups Xports Isdn interface Isdn Configuration MenuSharing Isdn in the USA & Canada Connecting two Xports to the same Isdn circuitSharing Isdn worldwide Cell Phone Interfacing the Aux Audio InterfaceTelos Soundcard Emulator Connecting the Cell Phone to the XportInstallation Feeding the Xport from a computer over EthernetConfiguring Windows Sounds and Media Changing configurationSelecting a Playback Device Changing the playback volume Remote ControlIs Xport a Pots codec? Frequently Asked QuestionsCan I share an Isdn line between two Xports? What happens when the line is very bad?What about international calls? Tell me more about the Ethernet? So what is the Aux Interface connector for?Anything better possible with mobile phones? Where can I get answers to my technical questions?What to do if… Why does my Isdn Xport take so long to boot up?How can I tell if my Xport has the Isdn option? Is the line shared between the Xport and any other device? Can’t find the Isdn setup menuCan the Xport place a call to a Telephone? Can’t place a call using Isdn in Zephyr modeCan’t place or receive calls using Isdn AC mains requirements Technical & Installation InformationVentilation and ambient temperature Environmental ConsiderationsInstalling the Isdn option Echnical & Installation Ifnormation Enabling Phantom Power Line Input balanced ¼ TRS Specifications & WarrantyDelay round trip FemaleMonitor MIX OUT Floating Balanced ¼ TRS Mix POT set to Send Headphone OutputZephyr Xport Limited Warranty Ordering Isdn ReferencesTechnology Articles White Papers Output Xports Rear Panel

Zephyr Xport specifications

The Telos Zephyr Xport is a cutting-edge audio-over-IP codec that seamlessly revolutionizes the way audio is transmitted over networks. Renowned for its high-quality sound, this powerful codec is designed for both radio broadcast applications and professional audio environments, enabling efficient, reliable, and high-fidelity audio transport over IP networks.

One of the main features of the Zephyr Xport is its ability to handle multiple audio formats, including PCM, AAC, and MP3, which provides users with flexibility depending on their specific needs. Its ability to encode and decode audio ensures that broadcasters can deliver outstanding quality both on the air and in streaming applications.

The technology behind the Zephyr Xport includes advanced algorithms that minimize latency, making it ideal for live broadcasts where real-time transmission is crucial. With a low latency rate, users can enjoy audio transmission that is nearly instantaneous, a defining feature for any live event or remote broadcasting situation.

Another standout characteristic of the Zephyr Xport is its support for multiple network protocols, including RTP/RTCP, SIP, and POTS. This versatility allows integration with a wide range of existing equipment and infrastructures, facilitating easy implementation in various settings. Additionally, the codec boasts robust error correction and adaptive bitrate control to ensure audio clarity even in fluctuating network conditions, reducing the chances of dropouts or interruptions.

The user-friendly interface of the Zephyr Xport features an intuitive LCD display, making it easy for operators to configure settings, monitor audio levels, and manage network connections. With built-in web access, users can make adjustments and control the unit remotely, providing added convenience for situations where operators are away from the hardware.

Moreover, the Zephyr Xport is designed for durability and reliability, constructed to endure the demands of a fast-paced broadcast environment. Its compact design makes it suitable for rack mounting or portable use, allowing broadcasters to take it on location without hassle.

In summary, the Telos Zephyr Xport combines advanced audio processing technologies with user-friendly features, making it an essential tool for modern broadcasters. Its high-quality audio performance, low latency communication, versatile protocol support, and ease of use exemplify the future of audio transmission in the ever-evolving landscape of digital broadcasting. As the industry continues to embrace IP-based solutions, the Zephyr Xport stands out as a vital asset for any professional audio application.
Top Page Image Contents