Jensen Tools 100 Sereis user manual Grandstream Networks, Inc

Page 35

BudgeTone-100 User Manual

Grandstream Networks, Inc.

 

 

 

Send DTMF

DTMF Payload Type

Send Flash Event

Onhook

Threshold

NTP server

Default Ring

Tone

Send Anonymous

Anonymous

Method

Time to ring

Special Feature

Syslog Server

This parameter specifies the mechanism to transmit DTMF digits.

There are 3 modes supported: in audio, which means DTMF is combined in in- band audio signal (not very reliable with low-bit-rate codec); via RTP (RFC2833); or via SIP INFO.

Make sure this setting is synchronized with SIP server otherwise will not work.

This parameter sets the payload type for DTMF using RFC2833 Default is 101

Default is NO. If set to Yes, flash will be sent as DTMF event therefore the FLASH key to switch calls will NOT work.

Time period when cradle pressed (Hook Flash) to simulate FLASH. Adjust this time value will prevent user on hook carelessly to activate Flash/Hold and cause the phone ring back. Default is 800ms.

URI or IP address of the NTP (Network Time Protocol) server, which will be used by the phone to synchronize the date and time.

By default “System Ring Tone” is selected. All calls received that do not match any “incoming caller ID” number will generate the selected ring tone

-system, 1, 2 or 3.

The user can setup up one number on each of the ring tones 1, 2, and 3. When a call is received from one of these numbers, the respective ring tone will be generated.

If the ring tone does not exist, the system default ring tone will be played. For BT-100, ring 3 is not supported.

If this parameter is set to “Yes”, user ID will be sent as anonymous, essentially block the Caller ID from displaying.

This is decided by supported SIP server/proxy. Either “Use From Header” or “Use Privacy Header” depends on how SIP sever/proxy process the SIP header.

Allow user to adjust the ring time of the phone. Default is 60 seconds

Default is Standard. Choose the selection to meet some special requirements from Soft Switch vendors like Nortel, Sonus, Broadsoft, etc. End user please do not touch this parameter.

The IP address or URL of System log server, especially useful for ITSP (Internet Telephone Service Provider). End user don’t encourage to touch this part

- 35 -

Image 35
Contents BudgeTone-100 Series Table of Contents Grandstream Networks, Inc Welcome LCD InstallationInterconnection Diagram Warranty What is Included in the PackageSafety Compliances Product Overview Key FeaturesHardware Specifications Model BudgeTone-101 BudgeTone-102 Icon LCD Icon Definitions Basic OperationsGet Familiar with LCD/LED Key Button Key Button Definitions Get Familiar with KeypadMessage Make Phone Calls Make Calls using NumbersMake Calls using IP Address Call Waiting and Call Flashing Handset Mode, Speakerphone/Headset ModeAnswer an Incoming Call Call HoldAttended Transfer Call TransferBlind Transfer Conference Call Key Call Features Call FeaturesMenu Item Menu Functions Configuration GuideConfiguration with Keypad Display 7 G-711u Display 9 codE rEL Menu Item Menu Functions Access the Web Configuration Menu Configuration with Web BrowserStatus Configuration MenuNAT End User Password IP Address Basic SettingsGrandstream Networks, Inc Status Basic Settings Advanced Settings Advanced SettingsDisable Call-Waiting Send Dtmf All Rights Reserved Grandstream Networks, Inc Grandstream Networks, Inc Grandstream Networks, Inc MWI Grandstream Networks, Inc Syslog level Grandstream Networks, Inc Saving the Configuration Changes Click to relogin Rebooting the Phone from RemoteConfiguration through a Central Server Upgrade through Tftp Software UpgradeUpgrade through Http Http//support.solarwinds.net/updates/New-customerFree.cfm Managing Firmware and Configuration File Download Firmware and Configuration File Prefix and PostfixStep Restore Factory Default SettingHeadset Connection Cross Over Cable For Plantronic Headset C d D c Glossary of Terms Dtmf DNSDid DSPHttp Echo CancellationFXS DhcpNTP IP TelephonyIVR MTUSDP PstnRtcp RTPVoIP UDPVAD Vlan