ALTERNATE PROGRAMMING METHOD
FUNCTION CODE |
| LOCAL PROGRAMMING |
| TELEPHONE PROGRAMMING | ||
05 | Step 1 | Enter Function Code 05, then press #. | Step 1 | Enter Function Code 05 and | ||
|
|
|
|
| press #, one short beep sounds. | |
MANUAL ACCESS |
|
| OPEN:00 HOURS |
|
| |
|
|
|
| Step 2 | Enter the number of hours from | |
RELAY CONTROL |
|
|
|
| ||
Step 2 | Enter the number of hours from |
| energize the access relay, then press #. | |||
This command can be used to |
| |||||
| energize the access relay, then press #. |
| - OR - | |||
latch the access relay indefi nitely |
|
| ||||
or for a period of time, and to |
| - OR - |
| Enter the 99 to energize the access | ||
unlatch the access relay. |
|
| ||||
| Enter the 99 to energize the access |
| relay indefi nitely, then press #. | |||
|
|
| ||||
|
| relay indefi nitely, then press #. |
| - OR - | ||
|
| - OR - |
| Enter the 00 to | ||
|
| Enter the 00 to |
| access relay, then press #. | ||
|
| access relay, then press #. |
| Two long beeps and two | ||
|
| - OR - |
| short beeps will sound. | ||
|
| Enter ✱ to cancel this command. |
|
| ||
06 | Step 1 | Enter Function Code 06, then press #. |
|
| ||
|
|
|
|
|
| |
DIRECTORY CODE |
|
| DIR DIGITS: 3 |
|
|
|
|
|
|
|
|
| |
LENGTH | Step 2 |
|
|
|
|
|
The display shows the current value. |
|
| ||||
Selects 2 or 3 digits for the |
|
| ||||
| Enter 2 or 3, then press #. |
|
| |||
Directory Code length (factory |
|
|
| |||
default is 3 digits). |
| - OR - |
| NOT AVAILABLE | ||
NOTE: In |
| Enter ✱ to cancel this command. |
|
| ||
|
|
| ||||
|
|
|
|
|
| |
access data that has Directory |
|
|
|
|
|
|
Codes with more digits than the |
|
|
|
|
|
|
|
|
|
|
|
| |
Directory Code length number will |
|
|
|
|
|
|
be automatically adjusted to fi t. |
|
|
|
|
|
|
10 | Step 1 | Enter Function Code 10, then press #. |
|
| ||
|
|
|
|
|
| |
WELCOME DISPLAY |
|
| (BLANK DISPLAY) |
|
|
|
|
|
|
|
|
| |
TEXT | Step 2 |
|
|
|
|
|
Enter the new welcome message. A total of 32 |
| NOT AVAILABLE | ||||
The |
| |||||
| characters are allowed. The display will advance |
| ||||
a visitor a welcome message |
|
|
| |||
alternating with instructions on |
| to the lower line after the 16th character is |
|
| ||
how to fi nd and call a resident. |
| entered on the upper line. Enter # after each |
|
| ||
The welcome message can be |
| character, enter ## after the last character. |
|
| ||
customized to suit the installation. |
|
|
| |||
|
|
|
|
|
| |
|
|
|
|
|
|
|
30 | Step 1 | Enter Function Code 30, then press #. | Step 1 | Enter Function Code 30 and | ||
|
|
|
|
| press #, one short beep sounds. | |
COPY ACCESS |
|
| UNITS: |
|
| |
|
|
|
| Step 2 | Enter the number(s) (2, 3, and/or 4) | |
DATA ONLY FROM |
|
|
|
| ||
Step 2 | Enter the number(s) (2, 3, and/or 4) of all the |
| of all the | |||
MASTER TO |
| |||||
|
| then press #, one short beep sounds. | ||||
|
|
| ||||
|
|
|
| Step 3 | Enter 5 for verifi cation, then press #, | |
To synchronize programming |
|
| ARE YOU SURE ? 5 |
| ||
|
|
|
|
| two short beeps sound. (Any entry other | |
in |
|
|
|
|
| |
Directory Entries and | Step 3 | Enter 5 for verifi cation, then press #. |
| than 5# will cancel the command.) | ||
Entry Codes can copied from the | NOTE: To allow for | |||||
master unit to selected |
| - OR - | ||||
|
| communications, when executing this | ||||
CAUTION: This utility |
| Enter ✱ to cancel this command. |
| |||
|
| command remotely over the telephone, | ||||
command will overwrite ALL the |
|
|
|
|
| |
NOTE: The installer must setup the system as a |
| the system will disconnect your call | ||||
access data in the |
| |||||
selected. |
| installation before this command will operate. |
| after Step #3 then copy the data from | ||
|
|
|
|
|
| the master unit to the |
17