Linear RE-2 To Enter Programming Mode, To Exit Programming Mode & Save Changes, Call Forwarding

Page 24

RESIDENT PROGRAMMING QUICK REFERENCE

Some of the programming PPN’s may be commonly used by the resident. Following are quick references to the keystrokes required.

NOTE: The “###” is the default command prefi x. The following example assumes that the default has not been changed.

To Enter Programming Mode

Press: Master Code

Master Code = the current 6-digit Master Programming Code

To Exit Programming Mode & Save Changes

Press:

Re-entering a Command After a Mistake

If an incorrect entry, or an incorrect key is pressed during programming, to clear the keypad:

Press:

Adding a Entry Code

Press: Code Code Relay Time Zone

Code = The new entry code: 1-999999, depending on code length

Relay = Relay output entry code will activate:

1 = Relay #1 2 = Relay #2 3 = Both Relays

4 = Relay #1 as priority user (no access restrictions)

Time Zone = 0 = no time zone; 1-7 to restrict access per time zone 1-7

Adding a Temporary Entry code

Press: Code Code Relay Time Zone Number

Valid From Valid Thru

Code = The new entry code: 1-999999, depending on code length Relay = Relay output entry code will activate:

1 = Relay #1 2 = Relay #2 3 = Both Relays

Time Zone = 0 = no time zone; 1-7 to restrict access per time zone 1-7 Number = Number of times (1-255) that the entry code is allowed access Valid From = First date (MMDDYY) that the entry code is valid

Valid Thru = Last date (MMDDYY) the entry code is valid.

Removing a Single Entry Code

Press: Code Code

Code = The entry code to remove.

Suspend or Activate a Single Transmitter

Press: Facility ID Action

Facility = Facility code 1-16 of transmitter (0 = no facility code)

ID = 5-digit ID number of transmitter

Action: 0 = Suspend transmitter; 1 = Re-activate transmitter

22

Maximum Number of Visitor Rings

Press: Rings

Rings = 1-15 Rings maximum

Visitor Talk Time Limit

Press: Limit

Limit = 15-255 Seconds allowed

Call Waiting Feature On/Off

Press: Call Waiting

Call Waiting: 1 = ON; 2 = OFF

Call Forwarding

Press: Forwarding Time Zone Telephone Number

Extension Delay

Forwarding: 0 = Call forwarding feature OFF

1 = Call forwarding feature ON at all times

2 = Call forwarding feature ON (scheduled by Time Zone) Time Zone = 1-7 (Call forwarding feature active during this Time Zone) Telephone Number = Up to 11-digit telephone number

Extension = Up to 4-digit telephone extension number

Delay = 1-25 seconds (delay between telephone number and extension)

“Do Not Disturb” Privacy Feature On/Off

Press:

 

Privacy

Time Zone

Privacy:

0

= Privacy feature OFF

 

1

= Privacy feature ON (scheduled by Time Zone)

 

2

= Privacy feature ON at all times

Time Zone = 1-7 (Privacy feature active during this Time Zone)

Automatic Door/Gate Open Time

Press: Relay 1st Time Zone 2nd Time Zone

Relay: 1 = Relay #1

2 = Relay #2

1st Time Zone = Time Zone 1-7

2nd Time Zone = Time Zone 1-7 (enter “0” if the 2nd time zone is not used)

Setting Time Zones

Press: Time Zone Number Active Days Start Hour

Start Minute AM/PM End Hour End Minute AM/PM

Time Zone Number = 1-7

Active Days (Enter up to 8 digits):

1 = Sun; 2 = Mon; 3 = Tue; 4 = Wed; 5 = Thu; 6 = Fri; 7 = Sat; 8 = Holidays Start Hour = 1-12 Start Minute = 0-59 AM/PM: 0 = AM; 1 = PM

End Hour = 1-12 End Minute = 0-59 AM/PM: 0 = AM; 1 = PM

Setting the Holiday Days

Press: Holiday Number Month Day

Holiday Number = 1-10

Month = 1-12

Day = 1-31

Image 24
Contents RE-2 Contents FeaturesAccess Methods System FeaturesProduct Description OperationInstallation Information Component Locations Help ButtonWiring Diagram Typical Gate Installation WiringEntry System Mounting Pedestal MountingWall Mounting Recessed MountingTelephone Wiring Telephone Wiring OptionsMultiple Unit Installations Command Prefix for Multiple UnitsControl Wiring Gate ControlDoor or Pedestrian Gate Control POWER, BATTERY, & Ground Wiring Power WiringBackup Battery Optional Remote AntennaOptional Keyswitch Keyswitch InstallationOptional Remote Keypad Camera Installation Optional Color Cctv CameraProgramming Access Programming with a ComputerSystem Requirements Setting UP a Windows XP DIAL-UP Network Connection Programming with a Local Telephone or the Unit’s Keypad Remote Programming with a TelephoneProgramming Reference Programming ControlBasic System Programming Entry Code ProgrammingTransmitter Programming Telephone ProgrammingAdvanced System Programming Press Obstacle Facility ID Press AddressPress Input Type Press CountSystem Adjustments Speakerphone VolumeDigital Speech Volume RE-2 Operation To Enter Programming Mode To Exit Programming Mode & Save ChangesRe-entering a Command After a Mistake Call Waiting Feature On/OffSpecifications Dimension DrawingTroubleshooting Programming Worksheet Time ZonesRelay # Time Zone Linear Limited Warranty Important Wireless Information