VTech VT2900 To program, the handset must be, There are two different ways to dial out a number

Page 14

ADVANCED FUNCTIONS

ADVANCED FUNCTIONS

Programming The Ringer

The handset ringer is capable of four different types of ringer tones for each line. The following sections detail how to change the different tones and to turn off a ringer on the handset.

Changing Ringer Tones

To program, the handset must be

OFF.

To select a different ringer type do the following:

Press and hold PROG until the PROG symbol appears on the display.

Press the # key.

Press:

1 for Handset LlNE 1

2 for Handset LlNE 2

3 for Baseset LlNE 1

4 for Baseset LlNE 2

ringer. The LCD will show what ringer is being programmed.

IPROGI

Press 1,2,3 or 4 to select a ringer

type.

Press MEM or OFF to store.

PROGRAMMING

THE RINGER TYPE

HANDSET MUST BE OFF

PRESSAND HOLD PROG

UNTILTHE PROG

SYMBOLAPPEARS

ON THE DISPLAY

3 for Baseset LlNE 1

4 for Baseset LINE 2

PRESS 1 2 3 or 4 TO SELECT^ ~ ~ N G TYPER

PRESS MEM or OFF TO STORE THE RINGER

Turning Off The Ringer

To turn off the ringer for a particular line do the following:

Press and hold PROG until the PROG symbol appears on the display

Press the # key

Press 1 for Handset LlNE 1 ringer, 2 for Handset LlNE 2 ringer.

Press 5 to turn off the ringer Press MEM or OFF to store.The

base ringers are controlled by ONIOFF switches.

Checking The Ringer Type

To test the present ringer type for a particular line do the following:

Press and hold PROG until the PROG symbol appears on the display

Press the # key

Press 1 for Handset LlNE 1 ringer, 2 for Handset CINE 2 ringer, 3 for Base LlNE 1 ringer, or 4 for Base LlNE 2 ringer

Press 0 to test the ringer Press MEM or OFF to exit

PROG and CLEAR Functions

The PROG and CLEAR functions can be accessed by pressing and holding the relevant key. For example, to clear the display, press and hold the CLEAR key for 2 seconds until the display is cleared. To enter program mode press and hold the MEM key for 2 seconds.

Advanced Dialing

There are two different ways to dial out a number:

1Press the LlNE key and wait for a dial tone. Then dial out the number you want either manually, using MEMORY (MEM) dialing or using

REDIAL.

2Enter the number you wish to dial onto the display first. Then press the LlNE key. This will dial out the number which is displayed on the LCD.

NOTE: The phone will dial out any number which is shown on the display. If you do not want to dial the number shown on the LCD, it can be changed by:

Use the CNFIBSP key to backspace one digit for each keypress. Additional digit$ can be entered. Press a LlNE key to dial the new number.

Press and hold CLEAR until the display is cleared, then dial normally.

Press the OFF key to clear the display, then dial normally. Wait for the display to clear, then .press LlNE and enter the number you wish to dial.

Changing Channels

In the unlikely event you notice interference when using your handset, press the INTCMICHAN key to switch to another channel. The display will briefly show the new channel number.

This has nothing to do with your two phone lines - only the radio link between the handset and base.

If the noise continues, see 'INCASE OF DIFFICULTY' onpage 30.

CHANGING

CHANNELS

In the unlikely event you notice interference

when using your

handset, press the

INT.COM/CHAN key to switch to a new channel

Image 14
Contents WEiI Table of Contents Programmable Ringer Types Digital Volume Adjust IntroductionintroductionIits Impossible to OVER- I Charge the Batteries Discard the old battery pack. DontReplacing the Batteries Replacing The Handset Batteries Follow the steps belowImportant Safety Instructions E a d and understand all instructionsSetting Up Your VT2900 Getting StartedGetting Started Wall Mounting Pack Before USELINE1 Wall Mounting LCD DisplayLINE2 NameHandset Keypad Baseset Keypad Set Base Ringer switches to on Quick Reference GuideVolume Control Keys Basic OperationRedial Joining a Handset ConversationFlash Advanced Functions To end a conference callHandset, press To program, the handset must beThere are two different ways to dial out a number To program a Memory location, do the following Memory DialingPress the LlNE key to get a dial tone Match it will dis~lavthe number Dial it out Memory Dialing MaintenanceIf you get Error displayed during Press and hold Prog Enter Press MEMOUT of Range Indication Case of Difficulty Make sure the Base Ringer are Set to on YOU Hear Other Calls While Using Your PhoneBase does not Ring Common Cure for Electronic EquipmentFCC and IC Regulations Technical Specifications Transmit FrequencyVT2900 Cordless Telephone Wall Mounting Template