VTech VT2900 manual Replacing the Batteries, Iits Impossible to OVER- I Charge the Batteries

Page 4

REPLACING THE BATTERIES

REPLACING THE BATTERIES

Charging the handset batteries

The handset of your VT2900 cordless telephone is poweredby rechargeable batteries. They charge automatically whenever the handset is in the base. You should charge the batteries for 24 hours when you first receive your phone. You'llknow the batteries need charging when:

The phone emits a dual-tone warning when you press the LINE or INTCM keys.

The battery symbol is flashing. The handset seems completely dead, the LCD is completely clear and the handset does not beep when you press the keys.

To Charge The Batteries

To charge the batteries, place the handset in the base unit. The CHARGE indicator will light to show the handset is seated properly and the batteries are charging. The CHARGE indicator will flash if the handset battery is not charged enough for the handset to operate. Once the battery

reaches the minimum level needed to operate, the CHARGE indicator will illuminate steadily and the battery will continue to charge up to its full potential. It is recommended that the battery be charged for 24 hours during the initial charge. After this initial charging, an overnight charge of 8 to 10 hours should be sufficient to fully charge the battery. You can use your telephone before that with diminished capacity, but it is best to let them charge fully. To maximize the charge capacity of the NiCad battery pack, recharge the battery for several cycles. The meximum battery life between charges is 5.5 hours of continuous talk time or 6 days of standby.

IIT'S IMPOSSIBLE TO OVER- I CHARGE THE BATTERIES

If the Batteries Don'tRecharge The battery pack can be recharged many, many times but if you get a low-battery signal even after 24 hours of charging, the battery pack should be replaced.

To purchase replacement battery packs, call VTECH Cornmunicat- ions at 1-800-624-5688.

In Canada, call VTECH Electronics at 604-273-5131.

Replacing The Handset Batteries

Follow the steps below:

1.Remove the battery case by pressing down on the release tab above the battery and then sliding

the batten/ downward.

t

I

BATTERY CONNECTION

 

2.Discard the old battery pack. Don't

put the old battery pack in a trash compactor or a fire - it could burst.

3.Slide the new battery pack on its track up until it is firmly in place.

4.The new battery pack must be charged before using your telephone. Place the handset in the cradle of the base unit to allow it to charge for 24 hours.

CAUTION:

To Reduce the Risk of Fire or Injury to Persons, Read and Follow the Instructions

1.Use only VTECH battery.

2.Do not dispose of the battery in a fire. The cell may explode.

IMPORTANT : Do not dispose of this battery into household garbage. For information on recycling or proper disposal,~consultyour local solid waste collection or disposal organization.

3.Do not open or mutilate the battery. Released electrolyte is corrosive and may cause damage to the eyes or skin. It may be toxic if swallowed.

4.Exercise care in handling batteries in order not to short the battery with conductingmaterialssuch as rings, bracelets, and keys. The battery or conductor may overheat and cause burns.

Image 4
Contents WEiI Table of Contents Programmable Ringer Types Digital Volume Adjust IntroductionintroductionDiscard the old battery pack. Dont Replacing the BatteriesIits Impossible to OVER- I Charge the Batteries Replacing The Handset Batteries Follow the steps belowImportant Safety Instructions E a d and understand all instructionsSetting Up Your VT2900 Getting StartedGetting Started Wall Mounting Pack Before USEWall Mounting LCD Display LINE2LINE1 NameHandset Keypad Baseset Keypad Set Base Ringer switches to on Quick Reference GuideVolume Control Keys Basic OperationFlash Joining a Handset ConversationRedial Advanced Functions To end a conference callThere are two different ways to dial out a number To program, the handset must beHandset, press Press the LlNE key to get a dial tone Memory DialingTo program a Memory location, do the following Memory Dialing Maintenance If you get Error displayed duringMatch it will dis~lavthe number Dial it out Press and hold Prog Enter Press MEMOUT of Range Indication Case of Difficulty YOU Hear Other Calls While Using Your Phone Base does not RingMake sure the Base Ringer are Set to on Common Cure for Electronic EquipmentFCC and IC Regulations Technical Specifications Transmit FrequencyVT2900 Cordless Telephone Wall Mounting Template