Polycom DOC2548A manual General Installation Precautions, Rack Mount Safety Precautions

Page 13

Polycom RMX 4000 Hardware Guide

General Installation Precautions

Attention:

The RMX 4000 can weigh up to 40kg when all slots are occupied. Two people are required to lift the MCU out of the box and also when installing it in a rack.

Use a regulating uninterruptable power supply (UPS) to protect the RMX 4000 from power surges and voltage spikes, to keep your MCU operating in case of a power failure. The RMX 4000 requires either two (DC) or three (AC) power supply cables, each connected to a power supply.

Allow the power supply units to cool before touching them.

When handling electronic components, standard anti-static precautions must be observed:

Wear a grounding strap

Handle cards by their edges only and do not touch their components or connector pins

Keep components in anti-static bags, when not installed in the RMX 4000

Rack Mount Safety Precautions

The following precautions should be followed when installing the

RMX 4000 on a rack:

The RMX 4000 has a height of 6U. Ensure this space is available on the rack.

Ensure that the leveling jacks on the bottom of the rack are fully extended to the floor with the full weight of the rack resting on them.

In a single rack installation, stabilizers should be attached to the rack.

In multiple rack installations, the racks should be coupled together.

Always make sure the rack is stable before extending a component from the rack.

You should extend only one component at a time - extending two or more simultaneously may cause the rack to become unstable.

Before you install the rails, determine the placement of each component in the rack.

Install the heaviest components on the bottom of the rack first, and then work up.

1-7

Image 13
Contents Polycom RMX 4000 Hardware Guide USA Συμμορφωνεται Προσ ΤΙΣ Ουσιωδεισ Απαιτησεισ ΚΑΙ ΤΙΣ Russian Communication Certificate Regulatory NoticesTable of Contents Component Replacement Hardware Description Power Consumption Power SupplyPhysical IP ProtocolsFollowing table summarizes the different system capacities System CapacitiesSystem Functions Capacity Card Resources Type MPM+ Resource CapacitiesHD720p HD1080p @30fps @60fps MPM+ CIF Resource Type Maximum Capacity 4 MPM+ CardsSite Safety Requirements Safety RequirementsRack Mount Safety Precautions General Installation PrecautionsUnpacking the RMX Installing the RMXPolycom RMX 4000 Hardware Guide Standalone RMX 4000 Installation Installing the RMX in a Rack or as a StandaloneRack Mount Preparations Placing the RMX 4000 in a 19 Rack 2Installing chassis runners and RMX in a rack3RMX 4000 Rack Mount 4Removing and attaching 19 and 23 brackets Placing the RMX 4000 in a 23 RackTo reverse mount the RMX 4000 on a 19 rack Reverse Mounting the RMX 4000 in a RackConnecting the RMX 4000 to Power Sources Make sure that the power button is switched OFF on the RMX Connecting the RMX 4000 to AC PowerConnecting the RMX 4000 to -48DC Selv Power Type a Type B Types of DC Circuit Breakers installed on the RMXTo connect the cables AC and DC systems RTM-IP Connecting Cables on the RMXFor more information about specific card connections, see First-time Power-upRTM LAN on RMX 4000 Front Panel RMX 4000 ComponentsShows the front panel of an RMX 4000 DC system Component Description 9RMX 4000 AC Rear View RMX 4000 Rear Panel10RMX 4000 DC Rear View RTM-IPLAN 3 Cntl Following items appear on the RMX 4000 rear panelStandby button Toggle between CPU activation and standby RTM IsdnISDN/PSTN Clock Source AC Power Entry Module PEMComponent Slot Allocation DC Power Rail ModuleSlot ID/No Card/Component Requirement RTM ISDN/RTM Following items appear on the RMX 4000 front panel RMX 4000 Front Panel LEDsComponent LED Color DescriptionCard Insertion Initiated If during Card removal Initiated The cardCntl 4000 Unit RTM-IP RMX 4000 Rear Panel LEDsFollowing LEDs appear on the RTM-IP 4000 card LED Color Description NameFunction Name Following LEDs appear on the RTM LANFollowing LEDs appear on the RTM Isdn RTM IsdnComponent Replacement Component Replacement Handle Using the Modified PMC Compatible Ejector LeverReplacing the Cntl 4000 Module Replacing an AC Power Supply Module Replacing an AC Power Entry Module PEM Replacing a DC Power Rail Module PRM Component Replacement Carefully slide the Fan drawer out through the front panel Replacing the Fan DrawerInserting an Air Filter Optional in the Fan Drawer Removing the MPM+ Card from the MCU Replacing a Faulty MPM+ CardComponent Replacement Carefully slide the MPM+ card out through the front panel Installing the Replacement MPM+ CardReplacing a RTM Isdn Card Installing a New MPM+ Card in a Powered On RMXPRI Cables Replacing the RTM-IP Replacing the RTM LAN Replacing the Fabric Switch Module FSM