Polycom DOC2548A manual Component Replacement

Page 54

Chapter 2- Component Replacement

2Power down the card by partially opening the ejector levers until the blue HS LED on the card and the Control Unit start to flash.

Warning!

Once the removal sequence is initiated the process cannot be terminated and the HS LED flashes.

3The power off sequence for the interconnected MPM+ and RTM ISDN cards are initiated as follows:

All participant connections on the card are disconnected.

A fault is generated on the system.

For each disconnected participant, a participant disconnection event is written to the CDR with the disconnection cause Disconnected by Operator.

New participant connections are blocked when the card is removed.

If an RTM ISDN card is connected to the MPM+ card it is also powered off and all ISDN and PSTN participants are disconnected.

When an RTM ISDN card is removed, its resources are deducted from the Resource Report.

A Log File entry is written indicating MPM+ card removal.

Port usage is re-calculated and the Port Gauges and Video/Voice Port Configuration dialog box are updated.

4When the blue HS LEDs on the MPM+, RTM ISDN and Control Unit stop flashing and remain lit, unscrew the captive screws and move the ejector levers to their fully open position and remove the MPM+ card.

2-12

Image 54
Contents Polycom RMX 4000 Hardware Guide USA Συμμορφωνεται Προσ ΤΙΣ Ουσιωδεισ Απαιτησεισ ΚΑΙ ΤΙΣ Regulatory Notices Russian Communication CertificateTable of Contents Component Replacement Hardware Description Physical Power SupplyPower Consumption IP ProtocolsSystem Capacities Following table summarizes the different system capacitiesSystem Functions Capacity MPM+ Resource Capacities Card Resources TypeHD720p HD1080p @30fps @60fps MPM+ Resource Type Maximum Capacity 4 MPM+ Cards CIFSafety Requirements Site Safety RequirementsGeneral Installation Precautions Rack Mount Safety PrecautionsInstalling the RMX Unpacking the RMXPolycom RMX 4000 Hardware Guide Installing the RMX in a Rack or as a Standalone Standalone RMX 4000 InstallationRack Mount Preparations 2Installing chassis runners and RMX in a rack Placing the RMX 4000 in a 19 Rack3RMX 4000 Rack Mount Placing the RMX 4000 in a 23 Rack 4Removing and attaching 19 and 23 bracketsReverse Mounting the RMX 4000 in a Rack To reverse mount the RMX 4000 on a 19 rackConnecting the RMX 4000 to Power Sources Connecting the RMX 4000 to AC Power Make sure that the power button is switched OFF on the RMXConnecting the RMX 4000 to -48DC Selv Power Types of DC Circuit Breakers installed on the RMX Type a Type BConnecting Cables on the RMX To connect the cables AC and DC systems RTM-IPFirst-time Power-up For more information about specific card connections, seeRTM LAN on RMX 4000 Components RMX 4000 Front PanelShows the front panel of an RMX 4000 DC system Component Description RMX 4000 Rear Panel 9RMX 4000 AC Rear ViewRTM-IP 10RMX 4000 DC Rear ViewFollowing items appear on the RMX 4000 rear panel LAN 3 CntlRTM Isdn Standby button Toggle between CPU activation and standbyAC Power Entry Module PEM ISDN/PSTN Clock SourceDC Power Rail Module Component Slot AllocationSlot ID/No Card/Component Requirement RTM ISDN/RTM Component RMX 4000 Front Panel LEDsFollowing items appear on the RMX 4000 front panel LED Color DescriptionCard removal Initiated The card Card Insertion Initiated If duringCntl 4000 Unit Following LEDs appear on the RTM-IP 4000 card RMX 4000 Rear Panel LEDsRTM-IP LED Color Description NameFollowing LEDs appear on the RTM LAN Function NameRTM Isdn Following LEDs appear on the RTM IsdnComponent Replacement Component Replacement Using the Modified PMC Compatible Ejector Lever HandleReplacing the Cntl 4000 Module Replacing an AC Power Supply Module Replacing an AC Power Entry Module PEM Replacing a DC Power Rail Module PRM Component Replacement Replacing the Fan Drawer Carefully slide the Fan drawer out through the front panelInserting an Air Filter Optional in the Fan Drawer Replacing a Faulty MPM+ Card Removing the MPM+ Card from the MCUComponent Replacement Installing the Replacement MPM+ Card Carefully slide the MPM+ card out through the front panelInstalling a New MPM+ Card in a Powered On RMX Replacing a RTM Isdn CardPRI Cables Replacing the RTM-IP Replacing the RTM LAN Replacing the Fabric Switch Module FSM