Polycom DOC2548A manual Replacing a Faulty MPM+ Card, Removing the MPM+ Card from the MCU

Page 53

Polycom RMX 4000 Hardware Guide

5Open the filter tray, by unscrewing two screws on the tray.

6Insert the air filter into the filter tray.

7Close the filter tray, by tightening the two screws on the tray.

8Insert and slide in the Fan drawer.

9Push the Fan drawer firmly into the Backplane, making sure it is properly seated in its slot.

10Tighten the captive screws on the front panel of the Fan drawer to the chassis.

11Turn ON the RMX 4000.

It is recommended that the air filter be replaced or cleaned every six months.

Replacing a Faulty MPM+ Card

Removing the MPM+ Card from the MCU

All MPM+ cards can be installed or removed while the RMX 4000 is powered on and operating.

Prior to removing an MPM+ card the captive screws must be unscrewed and the ejector levers must be opened to initiate a “power down” on the card.

1If applicable, loosen the captive screws and remove the slot cover.

2-11

Image 53

Contents Polycom RMX 4000 Hardware Guide USA Συμμορφωνεται Προσ ΤΙΣ Ουσιωδεισ Απαιτησεισ ΚΑΙ ΤΙΣ Russian Communication Certificate Regulatory NoticesTable of Contents Component Replacement Hardware Description Power Consumption Power SupplyPhysical IP ProtocolsSystem Functions Capacity System CapacitiesFollowing table summarizes the different system capacities HD720p HD1080p @30fps @60fps MPM+ MPM+ Resource CapacitiesCard Resources Type CIF Resource Type Maximum Capacity 4 MPM+ CardsSite Safety Requirements Safety RequirementsRack Mount Safety Precautions General Installation PrecautionsUnpacking the RMX Installing the RMXPolycom RMX 4000 Hardware Guide Rack Mount Preparations Installing the RMX in a Rack or as a StandaloneStandalone RMX 4000 Installation Placing the RMX 4000 in a 19 Rack 2Installing chassis runners and RMX in a rack3RMX 4000 Rack Mount 4Removing and attaching 19 and 23 brackets Placing the RMX 4000 in a 23 RackTo reverse mount the RMX 4000 on a 19 rack Reverse Mounting the RMX 4000 in a RackConnecting the RMX 4000 to Power Sources Make sure that the power button is switched OFF on the RMX Connecting the RMX 4000 to AC PowerConnecting the RMX 4000 to -48DC Selv Power Type a Type B Types of DC Circuit Breakers installed on the RMXTo connect the cables AC and DC systems RTM-IP Connecting Cables on the RMXRTM LAN on First-time Power-upFor more information about specific card connections, see RMX 4000 Front Panel RMX 4000 ComponentsShows the front panel of an RMX 4000 DC system Component Description 9RMX 4000 AC Rear View RMX 4000 Rear Panel10RMX 4000 DC Rear View RTM-IPLAN 3 Cntl Following items appear on the RMX 4000 rear panelStandby button Toggle between CPU activation and standby RTM IsdnISDN/PSTN Clock Source AC Power Entry Module PEMSlot ID/No Card/Component Requirement DC Power Rail ModuleComponent Slot Allocation RTM ISDN/RTM Following items appear on the RMX 4000 front panel RMX 4000 Front Panel LEDsComponent LED Color DescriptionCard Insertion Initiated If during Card removal Initiated The cardCntl 4000 Unit RTM-IP RMX 4000 Rear Panel LEDsFollowing LEDs appear on the RTM-IP 4000 card LED Color Description NameFunction Name Following LEDs appear on the RTM LANFollowing LEDs appear on the RTM Isdn RTM IsdnComponent Replacement Component Replacement Handle Using the Modified PMC Compatible Ejector LeverReplacing the Cntl 4000 Module Replacing an AC Power Supply Module Replacing an AC Power Entry Module PEM Replacing a DC Power Rail Module PRM Component Replacement Carefully slide the Fan drawer out through the front panel Replacing the Fan DrawerInserting an Air Filter Optional in the Fan Drawer Removing the MPM+ Card from the MCU Replacing a Faulty MPM+ CardComponent Replacement Carefully slide the MPM+ card out through the front panel Installing the Replacement MPM+ CardReplacing a RTM Isdn Card Installing a New MPM+ Card in a Powered On RMXPRI Cables Replacing the RTM-IP Replacing the RTM LAN Replacing the Fabric Switch Module FSM