Uniden UIP312 manual Quick Installation, Installing the Phone, DC-IN-18V

Page 11

6. Quick Installation

WARNING

The minimum requirements for using UIP312 are network configuration such as DHCP, IP Address, Net Mask, Gateway, DNS, etc., and GK address and alias configuration.

If above requirements are not satisfied, consult your network administrator.

6.1Installing the Phone

Unpack all the contents you received with your Phone.

Connect your activated Local Area Network (LAN) cable to the UPLINK port on the back of the Phone as shown in Figure 1

Connect the power adapter to an AC outlet and connect the jack to the DC-IN-18Von the back of the Phone (See Note).

If you use this phone with a PC, connect one end of the UTP cable (2m) to the Downlink port and the other end to your PC’s LAN card. (The Phone has an internal SWITCH HUB in itself.)

(DC-IN-18V)

Figure 1

UPLINK DOWNLINK

Note: Use only the power adapter provided by manufacturer. Some adapters provide too much voltage and can damage the phone. If the adapter does not provide enough power, the phone will not operate.

Page 7

Image 11

Contents User Guide V V1.2.8, BootromRevision History Table of Contents Iii Using the Setup menusSafety Information About This Guide IntroductionPackage Contents Phone Description UP , Down How the Keys WorkDial Pad Volume Keys have multiple functionsDC-IN-18V Quick InstallationInstalling the Phone Plantronics TriStar H81, GN Netcom Headset How to Use the Headset and Headset AdapterUsing Power over LAN POL Placement of the PhoneRegistration state How to Use the Multi-Line FeaturesDescription Network state iconMissed Call state Using LINE1 or LINE2 keyDND state Dialing state Receiving a call When there is one incoming callOff hook state Waiting Call When there are two incoming calls at the same timeFlash button let you switch between the two calls TIP Waiting Call Disconnecting a call using the handset Disconnecting a callDisconnecting when a single line is in use Disconnecting when a Multiple lines are in useTIP Reminder Ring Disconnecting a call using the speakerphone buttonPhone Operation How to Use the Handset and SpeakerphoneAdjusting the Handset and Speakerphone Volume Adjusting the Ringer VolumeRinger Volume control Handset Volume controlSpeakerphone Volume control Headset Volume controlHolding a call Muting a callRedialing the last number dialed Call information Caller IDHeadset audio path While you were using the handsetWhile you were using the speaker phone Inputting Characters Dial Pad Alphanumeric Characters H235PasswordNumbers Only 3 4 5 6 7 8 9 0 * #Menu Structure Using the Menu OptionsCall History How to go to Call history MenuOutgoing Calls Incoming Calls TIP Example Speed Dial One Touch DialingTIP Smart way to use Speed dial How to Set Up Your Speed Dial See 8.10 Inputting Characters How to Use Speed Dial Dialing & Modifying Using Menu Dialing Using Function key VMS Voice Messaging System Number Phone SettingHow to Use Phone Setting How to setup VMS NumberSee 8.10 Inputting Characters Ring Type Display Name Phone Function Do Not Disturb Disable RedialSystem New Password Password can be from one to four digits. ※ Input Number Only Select Change Password Change PasswordClear Password Time Auto and Manual Auto ModeSelect Time Server Mountain AtlanticEastern CentralManual Mode Country Service Provider Country & SP Service ProviderReboot Information Version Network Select Address IP PhoneSelect Jitter Buffer Using the Setup menus Page Alias Number Phone Number Page Select H235 Password 10.1.3 H235 PasswordVoice Select Codec Select G.711 Buffer Jitter BufferSelect G.729A Buffer Select G.723.1 BufferPriority Signal DiffServSelect Signal DiffServ Select Voice DiffServ Voice DiffServIP Address Duplication Upgrade Pending Auto UpgradeDisplay Information Dhcp ExpiredWhile Using Troubleshooting GuideFrequently Asked Questions Federal Communications Commission FCC Statement FCC StatementGlossary VoIP IP TelephonyJitter MAC address