Uniden UIP312 manual Safety Information

Page 5

1. Safety Information

Utmost care and attention has been devoted to quality standards in the manufacture of your new Phone. Safety is a major factor in the design of every set. But, safety is your responsibility too.

To avoid injury and damage to the phone, please follow these important safety instructions when installing, using your phone.

1.To reduce the risk of an electrical shock, do not disassemble this phone. There are no user serviceable parts. Opening or removing covers may expose you to hazardous voltages. Incorrect reassembly can cause an electrical shock.

2.Never push objects of any kind into this phone’s housing slots since such objects may touch hazardous voltage points or short out parts that could result in a risk of an electrical shock.

3.Only use Unshielded Twisted Pair (UTP) Category 5 Ethernet cable to connect to this phone’s RJ-45 ports (Uplink and Downlink).

4.Always use this phone with the required power source. The proper power source required for this phone is written on the power adaptor you received with this phone. If you are unsure of the type of power supplied to your premises, consult your local power company before installing this phone. Use only the adaptor provided.

(Output: DC 18V/ 600mA, (-)---(o---(+))

5.Do not connect or disconnect cables during an electrical storm.

6.Do not connect this phone directly to a standard telephone line. Although the RJ11 connector for a traditional telephone fits into the RJ-45 ports of this phone, the electrical interfaces are not compatible and the phone will not work.

7.Do not connect to headset connector any unfloating device, such as PC or amplifier, which may result ground loop. Use non-amplifier headset only.

8.Disconnect the power to this phone and have it checked by a qualified service personnel if any of the following occurs:

•the power supply cord or plug is damaged or frayed

•the phone was exposed to water or had liquid spilled on it

•the phone has been dropped or the cabinet has been damage

•after following the User Guide, the phone does not operate properly

Page 1

Image 5

Contents User Guide V V1.2.8, BootromRevision History Table of Contents Iii Using the Setup menusSafety Information About This Guide IntroductionPackage Contents Phone Description UP , Down How the Keys WorkDial Pad Volume Keys have multiple functionsDC-IN-18V Quick InstallationInstalling the Phone Plantronics TriStar H81, GN Netcom Headset How to Use the Headset and Headset AdapterUsing Power over LAN POL Placement of the PhoneDescription How to Use the Multi-Line FeaturesNetwork state icon Registration stateMissed Call state Using LINE1 or LINE2 keyDND state Dialing state Receiving a call When there is one incoming callOff hook state Waiting Call When there are two incoming calls at the same timeFlash button let you switch between the two calls TIP Waiting Call Disconnecting when a single line is in use Disconnecting a callDisconnecting when a Multiple lines are in use Disconnecting a call using the handsetTIP Reminder Ring Disconnecting a call using the speakerphone buttonAdjusting the Handset and Speakerphone Volume How to Use the Handset and SpeakerphoneAdjusting the Ringer Volume Phone OperationSpeakerphone Volume control Handset Volume controlHeadset Volume control Ringer Volume controlHolding a call Muting a callRedialing the last number dialed Call information Caller IDHeadset audio path While you were using the handsetWhile you were using the speaker phone Inputting Characters Dial Pad Alphanumeric Characters H235PasswordNumbers Only 3 4 5 6 7 8 9 0 * #Menu Structure Using the Menu OptionsCall History How to go to Call history MenuOutgoing Calls Incoming Calls TIP Example Speed Dial One Touch DialingTIP Smart way to use Speed dial How to Set Up Your Speed Dial See 8.10 Inputting Characters How to Use Speed Dial Dialing & Modifying Using Menu Dialing Using Function key How to Use Phone Setting Phone SettingHow to setup VMS Number VMS Voice Messaging System NumberSee 8.10 Inputting Characters Ring Type Display Name Phone Function Do Not Disturb Disable RedialSystem New Password Password can be from one to four digits. ※ Input Number Only Select Change Password Change PasswordClear Password Time Auto and Manual Auto ModeSelect Time Server Eastern AtlanticCentral MountainManual Mode Country Service Provider Country & SP Service ProviderReboot Information Version Network Select Address IP PhoneSelect Jitter Buffer Using the Setup menus Page Alias Number Phone Number Page Select H235 Password 10.1.3 H235 PasswordVoice Select Codec Select G.711 Buffer Jitter BufferSelect G.729A Buffer Select G.723.1 BufferPriority Signal DiffServSelect Signal DiffServ Select Voice DiffServ Voice DiffServDisplay Information Upgrade Pending Auto UpgradeDhcp Expired IP Address DuplicationWhile Using Troubleshooting GuideFrequently Asked Questions Federal Communications Commission FCC Statement FCC StatementGlossary Jitter IP TelephonyMAC address VoIP