Philips SE175 Declaration of conformity, Power requirements, To avoid damage or malfunction

Page 5

1Important safety instructions

Power requirements

This product requires an electrical supply of 100-240 volts AC. In case of power failure, the communication can be lost.

The voltage on the network is classified as TNV-3 (Telecommunication Network

Voltages), as defined in the standard EN

60950.

Warning

•• The Electrical network is classified as hazardous. The only way to power down the charger is to unplug the power supply from the electrical outlet. Ensure that the electrical outlet is always easily accessible.

To avoid damage or malfunction

Caution

•• Use only the power supply listed in the user instructions.

•• Use only the batteries listed in the user instructions.

•• Do not allow the charging contacts or the battery to come into contact with metal objects.

•• Do not open the handset, base station or charger as you could be exposed to high voltages.

•• Do not allow the charger to come into contact with liquids.

•• Risk of explosion if battery is replaced by an incorrect type.

•• Dispose of used batteries according to the instructions.

•• Always use the cables provided with the product.

•• For pluggable equipment, the socket-outlet shall be installed near the equipment and shall be easily accessible.

•• Handsfree activation could suddenly increase the volume in the earpiece to a very high level: make sure the handset is not too close to your ear.

•• This equipment is not designed to make emergency calls when the power fails. An alternative has to be made available to allow emergency calls.

•• Do not expose the phone to excessive heat

 

 

caused by heating equipment or direct sunlight.

 

h

•• Do not drop your phone or allow objects to

 

lis

fall on your phone.

 

Eng

•• Do not use any cleaning agents containing

 

 

alcohol, ammonia, benzene, or abrasives as

 

 

these may harm the set.

 

 

•• Do not use the product in places where there

 

 

are explosive hazards.

 

 

•• Do not let small metal objects come into

 

 

contact with the product. This can deteriorate

 

 

audio quality and damage the product.

 

 

•• Active mobile phones in the vicinity may cause

 

 

interference.

 

 

•• Metallic objects may be retained if placed near

 

 

or on the handset receiver.

 

 

 

 

 

About operating and storage temperatures

Operate in a place where temperature is always between 0°C to +35°C (32°F to 95°F).

Store in a place where temperature is always between -20°C and +45°C (-4° F to 113° F).

Battery life may be shortened in low temperature conditions.

Declaration of conformity

Hereby Philips Consumer Lifestyle, P&A, declares that the SE170/SE175 is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. You can find the Declaration of Conformity on www.p4c.philips.com.

This product has been designed, tested and manufactured according the European R&TTE directive 1999/5/EC. Following this directive, this product can be brought into service in the following countries:

EN 5

Image 5
Contents Register your product and get support at SE170 SE175 EC Declaration of Conformity Contents Station Auto clock Alarm clock Keypad lock Locate the handsetDeclaration of conformity Power requirementsVoltages, as defined in the standard EN 60950 To avoid damage or malfunctionDisposal of your old product and batteries Compliance with EMFEnvironmental information Congratulations on your purchase and welcome to Philips What is in the boxOverview of the phone Line cord Guarantee Quick start guideOverview of the base station Display icons Connect the base station Install the handsetGet started »» The handset starts charging Check the battery levelCheck the signal strength What is standby mode?Switch your handset On/Off Set the date and time formatEnd a call CallsMake a call Answer a call Adjust the earpiece volumeMute the microphone Turn off the ringer for all incoming callsTransfer a call Make a call to another handsetMake a conference call Toggle between callsDuring the conference call Enter text and numbers Phonebook Edit the direct access memory Direct access memoryEdit a record Delete a recordCall log Redial list Personalize the sounds Set the handset’s ringtone volumeSet the handset’s ringtone Set the key toneDial mode Call featuresSelect the recall duration Manage the area code»» ECO is displayed ECO modeFirst ring Alarm clock Extra featuresAuto clock Keypad lockUnlock the keypad Locate the handsetPress and hold »» The keypad is unlockedRegister the handsets Enhance the audio qualityUnregister the handsets Auto registrationPage Turn on/off the answering machine Set the answer modeSet the answering machine language Through the baseRecord an announcement AnnouncementsListen to the current announcement 1 Press Menu Select Answ Machine ANNOUNCEMENT, then press OK to ConfirmIncoming messages ICM Set the ring delayAccess the answering machine remotely Remote accessActivate/deactivate the remote access Behavior of the LED key on the base station Remote access commandsCall screening Default settings Display Technical dataHandset loses connection with the base Frequently asked questionsRichtlijn 1999/5/EG 1999/5/ECDirective 1999/5/CE Som framgår av direktiv 1999/5/EG0168
Related manuals
Manual 40 pages 13.1 Kb