Philips CD145 Install rechargeable Batteries, Slide out the battery cover Place the batteries as

Page 15

Note

The line adaptor may not be attached to the line cord. In this case, you have to connect the line adaptor to the line cord first before plugging the line cord to the line socket.

3.2Install rechargeable

batteries

Your CD145 is supplied with two rechargeable batteries. Before using the handset, install the batteries into the handset and fully charged them up.

1Slide out the battery cover

2Place the batteries as

indicated in the battery compartment and replace the battery cover.

3.3Place the handset on

the charging cradle Note

Charge the handset for at least 24 hours before using it for the first time.

When the battery is fully charged, the talk time of your CD145 is approximately 12 hours and the standby time is approximately 120 hours.

1Place the handset on the charging cradle of the base station.

2When the handset is fully

charged, is displayed.

3.4Configure your

phone

Before using your CD145, you need to configure it according to the country of use.

Depending on your country, country selection screen may not appear. In that case, you do not need to select the country code to configure your phone. After charging it for a few minutes, the country code selection screen appears. Follow these steps to configure your phone:

Getting started

13

Image 15

Contents Register your product and get support at CD145Page Table of contents Use more of your phone Call in progress Phonebook Call log Redial list SettingsHow to change the remote PIN Default settings Frequently asked questionsPower requirements Page Disposal instructions for batteries National recovery & recycling systemUsing GAP standard compliance Use one of the following disposal optionsElectric, Magnetic and Electromagnetic Fields EMF Line cord Congratulations on your purchase and welcome to PhilipsWhat’s in the box Telephone handset Base stationRedial/Flash key Overview Phone Handset ACall Log keyPhonebook key Talk keyProgram key Alphanumeric keypad GStar keyHHash key Call Transfer / Intercom / Conference Display icons on the handset Forward key Delete keyBackward key Event LEDConnect the base Station Getting startedPlace the handset on Charging cradle Note Install rechargeable BatteriesSlide out the battery cover Place the batteries as Configure your PhonePress Code Country Default outgoingTip Call from the call Log Make a call PrediallingCall is initiated Direct diallingEnd a call Call from PhonebookCall from the redial list Display shows the last number dialledRecall How to make a second call During a callHow to answer a Second call How to use IntercomConference call is initiated How to make an Internal callPress on the called handset AutomaticallyCall again How to find a handsetDuring the conference call External call is put on hold automaticallyIs shown on the display How to adjust earpiece volume During a callHow to store a number in the phonebook Idle mode Call in progress Mute/Unmute microphone During a callAll the phonebook entries are deleted How to access the phonebook Idle modeHow to edit the phonebook entry or Delete a number How to delete the entire phonebookSettings How to set the time 1 Press How to access the call logHow to delete the entire call log How to access Redial listHow to activate/deactivate the keypad lock How to set the ring MelodyHow to set the ring volume How to set the earpiece volumeHow to turn on/turn off the key Tone How to select recall timeHow to select dial Mode Current settings are displayedNew PIN is saved How to change the master PINHow to program voice mailbox Number How to access your voice mail numberHow to restore to default settings Your phone is reset to its default settingsUnchanged Press Enter your 4-digit PIN How to turn off Answering machine How to set answer delayHow to record your outgoing message How to play Outgoing message How to delete outgoing messageHow to select the default outgoing Message Incoming messages How to playHow to screen an incoming call How to remotely access yourPress and hold for two Seconds to delete all old messages How to change the remote PIN New remote access PIN Is savedKeys Description Items Default values Default settingsPoor audio quality Connection Handset does not switch onPhone does not work at all Communication is lost during a callCall Waiting call cannot be answered Is blinkingAppears Set-up Caller ID does not work properlyHandset is unable to register Caller does not hear meNoise interference on your radio or television Phonebook entry cannot be storedUnable to perform remote operation