Panasonic KX-TC1851NZB, KX-TC1851ALB operating instructions Recharge battery is

Page 53

Ò

Problem

Cause and Remedy

The display goes to the standby mode while viewing the Caller List.

³Do not pause for over 60 seconds while searching.

When a second call is received during a conversation, the unit does not display the new caller’s phone number.

³The line mode selection is incorrect. See page 13.

³Your Caller ID service provider does not support this feature.

(HANDSET\LOCATOR) does ³The handset is too far from the base unit.

not function.

 

³The handset is engaged in an outside

 

 

 

 

call or is viewing the Caller List/directory

 

 

 

 

list. Wait until the IN USE/CHARGE

 

 

 

 

indicator light goes out.

 

 

You cannot redial by

³If the last number dialled was more than

pressing (REDIAL/PAUSE).

32 digits long, the number will not be

 

 

 

 

redialled correctly.

 

 

 

 

³Access numbers entered after pressing

 

 

 

 

(TONE) will not be included when

 

 

 

 

redialling.

 

 

“Recharge battery” is

³Charge the battery fully (p. 11).

displayed, “

 

 

” flashes

 

or the unit beeps

 

 

intermittently.

 

 

 

 

 

 

 

You charged the battery fully, but “Recharge battery” is still displayed

and/or “ ” continues to flash.

³Clean the charge contacts and charge again (p. 12).

³Install a new battery (p. 49).

Useful Information

53

Page 52 Page 54
Image 53
Page 52 Page 54
Contents KX-TC1851NZB Charge the battery for about 6 hours before initial useFor your future reference Accessories includedBefore Initial Use Base Unit Location/Noise Battery ChargeFor Best Performance Contents Useful Information Handset Location of ControlsCaller ID Indicator p , 20 USE/CHARGE Indicator pBase unit Antenna p Charge Contacts pTalk 01-06-35 DisplayDirectory key Waiting 0266667777Connections SettingsBattery strength Installing the Battery in the HandsetDisplay prompt Battery strength Fully charged Medium Low flashing Needs to be rechargedAfter your Panasonic battery is fully charged p Battery informationOperation Approx. battery life RechargeMake sure the handset is in the standby mode Selecting the Line ModeDuring programming Programmable FunctionsProgram Press Ý or Ü to select On or Off Setting the Auto Talk FeaturePoints to Talk switching Ringer volume Selecting the Ringer VolumeSave directory 1Ringer volume 43 1=Yes RingerIf noise interferes with the conversation Making CallsTo redial the last number dialled TalkTo dial after confirming the entered number To select the receiver volumeTo redial after confirming the last number dialled LoudAuto Talk Answering CallsBacklit LCD display Backlit handset keypadHow caller information is displayed when a call is received Caller ID ServicePrivate name display Display shows the caller’s phone number after the first ringWhile the handset is on the base unit To check the number of new callsWhile the handset is off the base unit New calls 43 1=DirectoryTo check who has called, follow the steps below Using the Caller ListViewing the Caller List To return to the previous caller Ex. When you search from the most recent callTo exit the Caller List, press Display meaningOr Ü to enter the Caller List Calling Back from the Caller ListPress Ý or Ü repeatedly to find Desired callerFor New Zealand Users 76543210 =Next 1=Edit Editing the Caller’s Phone Number0276543210 =Next 1=Edit 00276543210 =Next 1=EditAdvanced Operation Edit 1Save directory 43 1=Yes Enter name 21 4=Next Storing Caller List Information in the DirectoryNew calls 43 1=Directory 0246813579 1220A JAN.12 √ Clear Erasing Caller List InformationTo erase a specific caller from the Caller List New call 43 1=Directory Exit 1All clear 43 1=Yes To erase all entries in the Caller ListStoring a Phone Number in the Direct Button One-Touch DiallerPress Ý Next key 1234567890123456 =Edit 1=Save Save DIRECT#Talk 1234567890123456 00-00-00 Dialling the Stored Number in the Direct ButtonStoring Names and Numbers in the Directory Using the DirectoryPress Ý Next key Press FWD/EDIT ß Save key 1Save directory Ringer volume 43 1=Yes Directory= 20 itemsPress Ý Next key Enter a phone number, up to 22 digits For New Zealand Users Number of times key is pressed Keys Steps for Entering Names and SymbolsIf you make a mistake while entering a name For example, to enter Tom Jones 0312345678 Finding Items in the DirectoryDirectory list =Caller’s list Index Table Dialling from the DirectoryKeys Index Frank TalkEditing an Item in the Directory Directory item you want to erase p Erasing an Item from the DirectoryHelen Press Clear Press FWD/EDIT ß Yes key or ClearAutomatic Security Code Setting Special FeaturesHandset Locator To stop paging, press HANDSET\LOCATOR again or press TalkFor Analog PBX Line/Long Distance Service Users How to Use the Pause ButtonFor Call Waiting Service Users in New Zealand Call Waiting and Caller ID Compatible1Program 43 1=Yes Recall ButtonSelecting the recall time Press Ý or Ü repeatedly until Points to Set recall timeDesired time is displayed Save DIRECT# 1Set recall time 43 1=YesWall Template Wall MountingTuck the telephone line cord inside Wall mounting adaptor, thenTo remove the handset holder To charge the batteryPlace the handset on Handset holder as shownUsing the Optional Headset Using the Belt ClipConnecting the optional headset to the handset To attach the belt clip To remove the belt clipBattery Replacement Adding Another Phone Clearer channel Problem Cause and RemedyBefore Requesting Help Before Requesting Help Recharge battery is For New Zealand Customers Safety Safety InstructionsInstallations Environment PlacementMedical Safety InstructionsFor New Zealand Users Only Instructions to customer InstallationImportant Information For Australia only Service difficulties PQQX12869YA-BM FM0800HK1090 D 62, 4-chome, Minoshima, Hakata-ku, Fukuoka 812-8531, Japan
Top Page Image Contents