Panasonic KX-TG3411BX Caller ID, Liquid damage, Registering a handset to the base unit

Page 24

TG341xBX(e).book Page 24 Thursday, March 3, 2011 1:47 PM

Useful Information

Caller ID

Problem

Cause/solution

Caller information is not

L You must subscribe to Caller ID service. Contact your

displayed.

service provider/telephone company for details.

 

L If your unit is connected to any additional telephone

 

equipment such as a Caller ID box or cordless telephone

 

line jack, plug the unit directly into the wall jack.

 

L If you use a DSL/ADSL service, we recommend

 

connecting a DSL/ADSL filter between the base unit and

 

the telephone line jack. Contact your DSL/ADSL provider

 

for details.

 

L Other telephone equipment may be interfering with this

 

unit. Disconnect the other equipment and try again.

Caller information is displayed

L Depending on your service provider/telephone company,

late.

the unit may display the caller’s information at the 2nd

 

ring or later.

 

L Move closer to the base unit.

Liquid damage

Problem

Cause/solution

Liquid or other form of moisture

L Disconnect the AC adaptor and telephone line cord from

has entered the handset/base

the base unit. Remove the batteries from the handset and

unit.

leave to dry for at least 3 days. After the handset/base

 

unit are completely dry, reconnect the AC adaptor and

 

telephone line cord. Insert the batteries and charge fully

 

before use. If the unit does not work properly, contact an

 

authorized service center.

Caution:

LTo avoid permanent damage, do not use a microwave oven to speed up the drying process.

Registering a handset to the base unit

1Handset:

{j/OK}

2{r}: Settingss{j/OK}

3{r}: Register HSs{j/OK}

4Base unit:

Press and hold {x} for about 5 seconds. (No registration tone)

L If all registered handsets start ringing, press {x} again to stop, then repeat this step. (KX-TG3412)

L The next step must be completed within 90 seconds.

5Handset:

Press {j/OK}, then wait until a long beep sounds.

L When the handset has been registered successfully, w stops flashing.

24

Image 24
Contents GHz Digital Cordless Phone Thank you for purchasing a Panasonic productTable of Contents Accessory information Supplied accessoriesModel composition Series Model No Base unit Handset QuantityAdditional/replacement accessories Accessory item Order numberFor your safety Important safety instructions BatteryFor best performance Base unit location/avoiding noiseSpecifications Other informationRoutine care Setting up Battery installationConnections Correct WrongBattery charging During a power failureBattery level Icon Battery levelControls HandsetBase unit Navigator keyInitial settings Dialing modeDisplay Date and timePause for PBX/long distance service users Adjusting the handset ringer volumeAnswering calls Auto talkUseful features during a call Phonebook Adding entriesFinding and calling from a phonebook entry Editing entries Erasing entriesChain dial Programmable settings Programming by scrolling through the display menusTG341xBXe.book Page 17 Thursday, March 3, 2011 147 PM Using Caller ID service Caller ID featuresCaller list Viewing the caller list and calling backEditing a caller’s phone number before calling back Erasing selected caller informationErasing all caller information Storing caller information to the phonebookVoice mail service Intercom Handset locatorTransferring calls, conference calls Making an intercom callError messages TroubleshootingGeneral use BusyBattery recharge Making/answering calls, intercomSettings sj/OK Register HS sj/OK Caller IDLiquid damage Registering a handset to the base unitWall mounting Base unit ChargerIndex TG341xBXe.book Page 27 Thursday, March 3, 2011 147 PM For your future reference