Grandstream Networks 486 user manual Software Upgrade, Upgrade through Http, Upgrade through Tftp

Page 26

HandyTone-486 User Manual

Grandstream Networks, Inc.

7Software Upgrade

7.1Upgrade through HTTP

To upgrade software, HandyTone ATAs can be configured with an HTTP server where the new code image file is located. For example, following URL in the HTTP Upgrade Server:

http://firmware.mycompany.com:6688/Grandstream/1.0.5.16

Here, firmware.mycompany.com is the FQDN of the HTTP server, “:6688” is the TCP port the HTTP server listening to, “/Grandstream/1.0.5.16” is the RELATIVE directory to the root dir in HTTP server. Thus, you can put different firmware into different directory as well.

Note: To enable HTTP firmware upgrade, “Auto Upgrade” field has to be set to Yes. In addition, the ATA will check the HTTP server in the number of days that is defined in “Check for new firmware every” field.

7.2Upgrade through TFTP

To upgrade software, HandyTone ATAs can be configured with a TFTP server where the new code image is located. The TFTP upgrade can work in either static IP or DHCP mode using private or public IP address. It is recommended to set the TFTP server address in either a public IP address or on the same LAN with the HandyTone ATA.

There are two ways to set up the TFTP server to upgrade the firmware, namely through voice menu prompt or via the HandyTone ATA’s Web configuration interface. To configure the TFTP server via voice prompt, follow section 5.1 with option 06, once set up the TFTP IP address, power cycle the ATA, the firmware will be fetched once the ATA boots up.

To configure the TFTP server via the Web configuration interface, open up your browser to point at the IP address of the HandyTone ATA. Input the admin password to enter the configuration screen. From there, enter the TFTP server address in the designated field towards the bottom of the configuration screen.

Once the TFTP server is configured, power cycle the HandyTone ATA.

TFTP checking is only performed during the initial power up. If the configured TFTP server is found and a new code image is available, the HandyTone ATA will attempt to retrieve the new image files by downloading them into the HandyTone ATA’s SRAM. During this stage, the HandyTone ATA’s LEDs will blink until the checking/downloading process is completed. Upon verification of checksum, the new code image will then be saved into the Flash. If TFTP fails for any reason (e.g., TFTP server is not responding, there are no code image files available for upgrade, or checksum test fails, etc), the HandyTone ATA will stop the TFTP process and simply boot using the existing code image in the flash.

TFTP may take as long as 1 to 2 minutes over Internet, or just 20+ seconds if it is performed on a LAN. It is generally recommended to conduct TFTP upgrade in a controlled LAN

26

Image 26
Contents HandyTone-486 For SW Release VersionTable of Contents Welcome Installation Top View Side ViewsWhat is Included in the Package Safety CompliancesKey Features Product OverviewHardware Specification Model HandyTone-486Basic Operations Get Familiar with Key Pad and Voice PromptDirect IP calls Make Phone CallsCalling phone or extension numbers Attended Transfer Voice Prompt with option 47, thenBlind Transfer Send and Receive Pstn Calls Through Pstn Line Port Call FeaturesCall Features Table LED Light Pattern Indication Pstn Pass ThroughConfiguring HandyTone-486 with Web Browser Configuration GuideConfiguring HandyTone-486 WAN IP through Voice Prompt Grandstream HandyTone 486 Configuration DMZ IP MAC Address Advanced User Configuration DMZ IPAdvanced Options Layer 2 QoS Use DNS SRV User ID is phone number LAN IP LAN IP LAN IP LAN IP LAN IP LAN IP LAN IP LAN IP G723 Rate Early Dial Offhook Saving the Configuration Changes Rebooting the HandyTone-486 from remoteConfiguration through a Central Server Upgrade through Tftp Software UpgradeUpgrade through Http Grandstream Networks, Inc Restore Factory Default Setting
Related manuals
Manual 34 pages 18.65 Kb