Uniden DS845 quick start Using Your Answering System

Page 26

Selecting the message record time:

You can set your answering system to record a message up to one or four minutes long.

One minute option : move the REC TIME switch to 1.

Four minutes option : move the REC TIME switch to 4.

Announce only feature:

The announce only feature plays an outgoing message, but it will not allow the caller to leave a message. Move the REC TIME switch to the ANN position.

The message counter LED displays when the system is on standby.

Pre-recorded outgoing message for Announce only feature is : “Hello, no one is available to take your call.” (twice)

 

 

 

 

 

 

 

 

 

RING TIME

REC TIME

 

2/4/TS

ANN/4/1

voice memo

greeting

volume

Selecting a PIN code:

speaker status

delete play

To play your messages from a remote location, you will need to enter a two digit Personal

Identification Number (PIN) code ( 0

0 9

9

(. To select a PIN, perform the

following steps.

until a tone sounds and the LED displays 00.

1.

On the base, press and hold pin

2.

To set the first number, press

or

repeatedly to scroll from 0 to 9. When

 

the desired number appears in the display, press

pin .

3.

To set the second number, press

or

 

to scroll from 0 to 9. When the

 

desired number appears in the display, press

pin . Then the entered PIN code is

 

announced.

 

 

 

Selecting Ring Time Switch:

The ring time/toll saver switch allows you to set the number of rings the caller hears before the answering system plays your outgoing message.

You can set the switch to answer after two rings or after four rings. Once the greeting has started, you can stop it when you pick up the call at the handset or base. In the TS (toll saver) position, the answering system picks up after 6 rings if you have new messages, and after 9 rings if there are none.

This way, if you call long distance to check your messages, you can hang up after the seventh ring to avoid billing charges.

 

 

 

 

 

 

 

 

 

RING TIME

REC TIME

 

2/4/TS

ANN/4/1

Using Your Answering System

Playing your messages

The base LED shows the number of total messages on the display. If the display is blinking, then there are new messages waiting for you. After you play your new messages you can then play old messages.

1. Press play

. The system announces the number of new and old messages, then

the incoming messages are played.

2.When all new messages have played, a tone is heard. The message counter LED stops flashing to indicate that all of the new messages have been reviewed.

3.After you have reviewed all your messages, you can play your old messages again. Press

play

and follow the instructions above.

20

Image 26
Contents Quick Start Guide Precautions Start AC Adaptor cord AC Adaptor into Raise the antennaIii Make sure the plug is the right way roundPress firmly until it clicks into place Handset on Base Unit To hang up press talkPlace the handset on the base Unit Remove the handset from the base and speak Auto TalkDelete one message Press new messages play firstPress during playback of messages Delete all messages After reviewing all messages pressContents Controls & Functions Rear of Base Unit Top of Base Unit Welcome Latest in 900 MHz Digital Spread Spectrum TechnologyIf any of these items are Belt ClipCard Your place of purchaseCleaning the battery contacts Battery use time per chargeWhen the battery charge becomes low Ringer tone and volumeTalk button Making and Receiving CallsBasic phone operation To answer a call phone ringingTo transfer from handset to base unit Call TransferRedialling a Call To transfer from base unit to handsetCall WAITING/FLASH Travelling OUT of RangeKEY Lock / Unlock With the Base Unit Storing Phone Numbers and NamesWith the Handset Display a Memory Number or Name Memory dialing from talk modeMemory Dialling from Standby Memory Dialing from the Base UnitYou would like to edit Screen displaysPress to move the pointer down to Erasing a Stored Number from the Base UnitMemory location you would like to edit Press select the confirmation screen is displayedWay radio feature using an optional handset PAGING/INTERCOMRemove the handset from its charger Different number to enable functions such as Call TransferRegistration Press flash/reg on the handset FigName tagging When the Telephone RingsCaller ID Deleting all Caller ID names/numbers Viewing the Caller ID Message ListDeleting Information from the Caller ID List Storing Caller ID messages in Memory dialing Using the Caller ID ListCalling a party from the Caller ID list Answer System FeaturesSetting Up Your Answering System Using Your Answering System Deleting Messages Call your telephone number Remote access away from homeRemote room monitor ThenTrouble Shooting Uniden New Zealand Limited One Year Limited WarrantyWarrantor Uniden Australia Pty Limited A.B.N 001 865Page Uniden Australia Pty Limited Uniden New Zealand Limited