Cobra Electronics MR HH425LI owner manual Ctcss and DCS Coding Mode, To Set Ctcss Code Entry

Page 29

Operating Your Radio

GMRS Mode

CTCSS Code Entry

CTCSS Code Number

50 English

Setup Mode Programming

GMRS Mode Programming

The GMRS (General Mobile Radio Service) feature is a land- mobile service available for short-distance, two-way communications in the USA. You must have a valid FCC license to communicate on these channels (see page 28).

Start from GMRS Standby mode to begin GMRS Setup programming. Press and hold the Call/Enter/Setup button for two (2) seconds to enter the programming mode.

CTCSS and DCS Coding Mode

Continuous Tone Controlled Squelch System (CTCSS) and Digital Coded Squelch (DCS) coding are used in two-way radio systems. These are sub-audible frequencies or digital tones that are sent continuously with speech to engage other radios with this feature. This feature is generally used between talk groups on shared channels. Only radios with the same subcode set will hear your transmission.

To Set CTCSS Code Entry:

1.The CTCSS code entry mode is the first mode that begins the GMRS Setup programming.

2.Display will show CTCSS icon and OFF icon flashing.

NOTE

If CTCSS was previously set to a Code number, display will show the current GMRS channel and flash the CTCSS icon and Code number.

3.Codes begin at 01 and go to 38, followed by OFF, and return back to 01 again. The last used GMRS channel will be shown in the large digit display.

NOTE

If CTCSS is On, then DCS must be Off. If DCS is On, then CTCSS must be Off.

4.Press Channel Up/Down button to change code number, or press and hold Channel Up/Down button to rapid advance (scroll).

5.Press Call/Enter/Setup button to save entry and move to the next setup programming mode.

Operating Your Radio

DCS Code Entry

CTCSS Code Number

VOX Mode On/Off

VOX Level

Setup Mode Programming

To Set DCS Code Entry:

1.Display will show DCS icon and OFF icon flashing.

NOTE

If DCS was previously set to a Code number, the display will show the current GMRS channel and flash the DCS icon and Code number.

2.Codes begin at 01 and go to 83, followed by OFF and return back to 01 again. Last used GMRS channel will be shown in the large digit display.

NOTE

If CTCSS is On, then DCS must be Off. If DCS is On, then CTCSS must be Off.

3.Press Channel Up/Down button to change code number, or press and hold Channel Up/Down button to rapid advance (scroll).

4.Press Call/Enter/Setup button to save entry and move to the next setup programming mode.

Voice Activated Transmit (VOX) Mode

The VOX Mode On or Off and VOX Sensitivity Level setup procedures are the next two settings in GMRS Mode Programming. Follow the same procedures on page 44, in Marine (VHF) Setup Programming, to set these functions.

After these two settings have been made, press Call/Enter/Setup button to save each entry and move to the next setup programming mode.

Nothing Comes Close to a Cobra® 51

Image 29
Contents How Your CobraMarine VHF/GMRS Radio Works Our Thanks to You Customer AssistanceFor Assistance in the U.S.A For Assistance Outside the U.S.ABacklit LCD Liquid Crystal Display Screen Radio Controls IndicatorsBacklit LCD Screen Product Features Signal Strength Meter Lithium-Ion Rechargeable Battery PackChannel Scan/Memory Scan Instant Channel 16/9Table of Contents Safety Training Information Important Safety InformationImportant Safety Information Always use only Cobra authorized accessoriesRecommendations for Marine Communication Recommendations for Marine CommunicationStation License VHF Marine FCC Licensing InformationInternational Station License Radio Call SignVHF Marine Radio Procedures Vessel Corsair is calling the vessel Vagabond VHF Marine Voice CallingVHF Marine Voice Calling VHF Marine Radiotelephone Calls VHF Marine Emergency Messages and Distress ProcedureIf You Hear a Distress Call Marine Emergency SignalsThree 3 spoken international emergency signals are Tell where you are Marine Distress ProcedureSay End message by sayingVHF Marine Channel Assignments 156.700 Rx Only 156.750 International Distress, Safety and Calling156.800 156.850 03A Government Only23A Government Only 20A Port Operations Port Operations, Ship Movement21A U.S. Government Only Canada Coast Guard Only Digital Selective Calling Voice communications not allowed 64A U.S. Government Only Canada Commercial Fishing81A U.S. Government Only Environmental Protection Operations GMRS/FRS Frequency Allocation and Compatibility Gmrs Communication Gmrs FCC LicensingGmrs Communication Gmrs FCC LicensingNoaa Test Alert System Noaa Weather Channels AlertNoaa Emergency Weather Alert Weather Frequency/ChannelSpecific Area Message EncodingSAME Alerts Specific Area Message Encoding Same AlertsIncluded in this Package Batteries and Charger Antenna, Wrist Strap Belt ClipWrist Strap Belt ClipAlkaline Batteries To Remove Battery Pack from RadioInitial Charge Volume Control Power/Volume/Squelch Controls Power On/Off ControlGetting Started Common Radio Functions All BandsSquelch Control Call/Enter/Setup Button To Lock or Unlock the ButtonsTalk Button Backlight/Key Lock ButtonTo Toggle Between H-M-L Power Modes High/Medium/Low H-M-L Power ButtonCall /Enter/Setup Button Scan ButtonSetup Mode Programming Setup Mode ProgrammingUSA/International/Canada Channel Maps To Set Channel Map Operating AreaTo turn VOX Mode On or Off Voice Activated Transmit VOX ModeVibrAlert Mode To set VOX Sensitivity LevelRoger Beep Mode Call Tone ModeKey Tone Mode To Set Call ToneTo Set DCS Code Entry Ctcss and DCS Coding ModeTo Set Ctcss Code Entry To Set DCS Code Scan Ctcss and DCS Code Scan ModeTo Set Ctcss Code Scan To Set Specific Area Message Encoding Same Alert On or Off To Set WX Alert On or OffTo Set WX Auto Search Scan On or Off Standby/Receive Transmit Marine VHF Standby ModeMarine VHF, Gmrs and WX Alert Standby Band Selections Standby/Receive and TransmitTransmit Tx and Receive Rx Modes Gmrs Standby ModeReceive Rx Icon Bar Graph Icon Transmit Tx Icon Bar Graph Icon To Transmit a MessageWX Alert Standby Mode Weather WX Standby ModeWX Auto Search Scan Mode Function WX Auto Search Scan function is OnAdvanced Operation Channel 16/9 ModeAdvanced Operation To Program or Edit the Tri-Watch Locations Tri-Watch ModeUsing Tri-Watch Tri-Watch Scan Mode Memory Locations To Exit Memory Location ModeTo Program Memory Locations To Recall a Stored Memory LocationMemory Location Scan Channel Scan ModeTo Enter Channel Scan Memory locations, seeUsing Rewind-Say-Again Rewind-Say-Again FeatureUsing Rewind-Say-Again to Record Audio Transmission ExampleSpecifications Maintenance TroubleshootingMaintenance TroubleshootingProduct Service Product ServiceLapel Speaker Microphone AccessoriesAccessories