Cobra Electronics MR HH425LI To Program Memory Locations, To Recall a Stored Memory Location

Page 37

Operating Your Radio

MEM/ESC Button

Memory Location Number

MEM Icon

Channel Up/Down Button

Channel Number

66 English

Advanced Operation

Memory Locations

Your radio has unlimited memory locations for storing your most frequently used channels. These memory locations can be selected individually or can be scanned. (See page 69 under Memory Location Scan.) You are also able to change bands for memory locations and scanning, allowing an unlimited amount of choice selection.

To Program Memory Locations:

1.Press and hold the MEM/ESC button for two (2) seconds. The Memory location number will start flashing and the MEM icon will be turned On.

2.Use the Channel Up/Down button to advance to the Memory location (00-99) you want to program.

3.Press the MEM/ESC button to select the Memory location. The Memory channel number will stop flashing and the channel number will start flashing.

4.Use the Channel Up/Down button to change to the channel you want to store into the selected Memory location.

5.Press the MEM/ESC button to program that channel. The Memory location number will flash again.

Repeat steps 2 through 5 to program as many additional memories as you want.

6.Press and hold the MEM/ESC button for two (2) seconds. This will return the radio to the Memory mode.

7.Press and release the MEM/ESC button again to return to the Marine or GMRS Standby mode.

Operating Your Radio

MEM/ESC Button

Memory Location Number

MEM Icon

Channel Up/Down Button

Channel Number

Advanced Operation

To Recall a Stored Memory Location:

1.Press the MEM/ESC button. The MEM icon will be turned On.

2.Press the Channel Up/Down button to select the memory location. If a memory location has been programmed, its associated channel will display on the LCD. Your radio is now in Marine or GMRS Standby mode on the selected memory location.

NOTE

In addition to using the Channel Up/Down button when selecting your memory channel, you can use the BAND button to select channels in the GMRS band.

To Exit Memory Location Mode:

Press the MEM/ESC button to return the radio to the Marine or GMRS Standby mode. The last channel used in Marine or GMRS Standby mode will now be displayed on the LCD and the MEM icon will disappear.

To Erase Stored Memory Locations:

1.Press and hold the MEM/ESC button for two (2) seconds. The memory location number will start flashing and the MEM icon will be turned On.

2.Use the Channel Up/Down button to advance to the memory location you want to erase.

3.Press the MEM/ESC button to select the memory location. The memory channel number will stop flashing and the channel number will start flashing.

4.Use the Channel Up/Down button to change to the channel to read “00” at the selected memory location.

5.Press the MEM/ESC button to erase that channel.

Repeat steps 2 through 5 to erase as many additional memories as you want.

6.Press and hold the MEM/ESC button for two (2) seconds. This will return the radio to Memory mode.

7.Press and release the MEM/ESC button again to return to Marine or GMRS Standby mode.

Nothing Comes Close to a Cobra® 67

Page 36 Page 38
Image 37
Page 36 Page 38
Contents How Your CobraMarine VHF/GMRS Radio Works Our Thanks to You Customer AssistanceFor Assistance in the U.S.A For Assistance Outside the U.S.ABacklit LCD Screen Product Features Radio Controls IndicatorsBacklit LCD Liquid Crystal Display Screen Signal Strength Meter Lithium-Ion Rechargeable Battery PackChannel Scan/Memory Scan Instant Channel 16/9Table of Contents Safety Training Information Important Safety InformationImportant Safety Information Always use only Cobra authorized accessoriesRecommendations for Marine Communication Recommendations for Marine CommunicationStation License VHF Marine FCC Licensing InformationInternational Station License Radio Call SignVHF Marine Radio Procedures VHF Marine Voice Calling VHF Marine Voice CallingVessel Corsair is calling the vessel Vagabond VHF Marine Radiotelephone Calls VHF Marine Emergency Messages and Distress ProcedureThree 3 spoken international emergency signals are Marine Emergency SignalsIf You Hear a Distress Call Tell where you are Marine Distress ProcedureSay End message by sayingVHF Marine Channel Assignments 156.700 Rx Only 156.750 International Distress, Safety and Calling156.800 156.850 03A Government Only21A U.S. Government Only Canada Coast Guard Only 20A Port Operations Port Operations, Ship Movement23A Government Only Digital Selective Calling Voice communications not allowed 64A U.S. Government Only Canada Commercial Fishing81A U.S. Government Only Environmental Protection Operations GMRS/FRS Frequency Allocation and Compatibility Gmrs Communication Gmrs FCC LicensingGmrs Communication Gmrs FCC LicensingNoaa Test Alert System Noaa Weather Channels AlertNoaa Emergency Weather Alert Weather Frequency/ChannelIncluded in this Package Specific Area Message Encoding Same AlertsSpecific Area Message EncodingSAME Alerts Batteries and Charger Antenna, Wrist Strap Belt ClipWrist Strap Belt ClipInitial Charge To Remove Battery Pack from RadioAlkaline Batteries Volume Control Power/Volume/Squelch Controls Power On/Off ControlGetting Started Common Radio Functions All BandsSquelch Control Call/Enter/Setup Button To Lock or Unlock the ButtonsTalk Button Backlight/Key Lock ButtonTo Toggle Between H-M-L Power Modes High/Medium/Low H-M-L Power ButtonCall /Enter/Setup Button Scan ButtonSetup Mode Programming Setup Mode ProgrammingUSA/International/Canada Channel Maps To Set Channel Map Operating AreaTo turn VOX Mode On or Off Voice Activated Transmit VOX ModeVibrAlert Mode To set VOX Sensitivity LevelRoger Beep Mode Call Tone ModeKey Tone Mode To Set Call ToneTo Set Ctcss Code Entry Ctcss and DCS Coding ModeTo Set DCS Code Entry To Set Ctcss Code Scan Ctcss and DCS Code Scan ModeTo Set DCS Code Scan To Set WX Auto Search Scan On or Off To Set WX Alert On or OffTo Set Specific Area Message Encoding Same Alert On or Off Standby/Receive Transmit Marine VHF Standby ModeMarine VHF, Gmrs and WX Alert Standby Band Selections Standby/Receive and TransmitTransmit Tx and Receive Rx Modes Gmrs Standby ModeReceive Rx Icon Bar Graph Icon Transmit Tx Icon Bar Graph Icon To Transmit a MessageWX Alert Standby Mode Weather WX Standby ModeWX Auto Search Scan Mode Function WX Auto Search Scan function is OnAdvanced Operation Channel 16/9 ModeAdvanced Operation Using Tri-Watch Tri-Watch Scan Mode Tri-Watch ModeTo Program or Edit the Tri-Watch Locations Memory Locations To Exit Memory Location ModeTo Program Memory Locations To Recall a Stored Memory LocationMemory Location Scan Channel Scan ModeTo Enter Channel Scan Memory locations, seeUsing Rewind-Say-Again Rewind-Say-Again FeatureUsing Rewind-Say-Again to Record Audio Transmission ExampleSpecifications Maintenance TroubleshootingMaintenance TroubleshootingProduct Service Product ServiceAccessories AccessoriesLapel Speaker Microphone
Top Page Image Contents