Cobra Electronics LI 4900WX Using Your Radio, For charging microTALK radios in desktop charger

Page 4
1. Press and hold the Talk button.
2. With the microphone about 2 inches (5 cm) from your mouth, speak in a normal voice.
3. Release the Talk button when you are finished talking and listen for a response.
You cannot receive incoming calls while pressing the Talk button.
Both radios must be tuned to the same channel/privacy code to communicate.
Communicating with Another Person
Press and hold the Power button until you
hear a series of audible tones indicating the radio is on.
Your microTALK radio is now in Standby mode, ready to receive transmissions. The radio is always in Standby mode, except when the Talk, Call or Power buttons are pressed.
Turning on Your microTALK Radio

Introduction

Insert Radio(s)

Using Your Radio

For charging microTALK radio(s) in desktop charger:

1.Insert radio(s) into desktop charger as shown.

2.Insert round connector of 120-volt adapter into jack on back of charger.

3.Plug 120-volt adapter into electrical outlet.

 

 

 

 

Introduction

Operation

Customer Assistance

Warranty

On/Off Power

If charging light is not on, check position of radio. Radio should be upright. The charge indicator light will stay on as long as the radio is in the charging well.

It normally takes about 15 hours to fully recharge battery pack. Battery pack will not be damaged if it stays in the charging well longer than that.

Note: To charge a single radio, you can bypass the desktop charger and simply insert the wall adapter’s round connector directly into the speaker/microphone/charge jack located on the top of the radio.

Use only the supplied rechargeable batteries and charger for recharging your Cobra microTALK radio.

Cobra recommends your radio is turned off while being charged.

Quick Start

1. Press and hold the Power button to turn on your radio.

2.Press the Channel Up or Channel Down button to select a channel.

Both radios must be tuned to the same channel/privacy code to communicate.

3.Press and hold the Talk button while speaking into the microphone.

4.When finished talking, release the Talk button and listen for a response.

2

Battery Low

 

Battery Low

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

When battery power is low, the Battery Low icon

 

 

 

 

 

 

 

will blink. Your batteries should be recharged.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Auto Battery Save

 

 

 

 

 

 

 

 

 

 

Your microTALK radio has a unique circuit

 

Battery Save Mode

 

 

 

 

 

 

 

 

designed to extend battery life. If there are

 

 

 

 

 

 

 

 

no transmissions for 10 seconds, the radio will

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

automatically switch to Battery Save mode and

 

 

 

 

 

 

 

 

the Power Saver icon will flash in the display.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

This will not affect the radio’s ability to receive

 

 

 

 

 

 

 

 

incoming transmissions.

 

Talk Button

2 Inches (5 cm) from Mouth

3

Image 4
Contents Making Life Easier and Safer For Assistance in the U.S.AAutomated Help Desk Customer Assistance OperatorsProduct Features Warranty and Trademark AcknowledgementLimited One-Year Warranty on Radios & Charger Trademark AcknowledgementCaring for YourmicroTALKRadio Replace battery compartment cover and belt clipEstimated operation time on full charge 10 hours Using Your Radio Battery LowAuto Battery Save For charging microTALK radios in desktop chargerTo toggle between high and low power Listening for a ResponseCall Button To alert another person that you are calling To Illuminate DisplayLock Feature Signal Strength MeterAuto Squelch/Maximum Range MicroTALK RangeMode Functions Scrolling through Mode FunctionsPrivacy Codes Set Ctcss Privacy CodesStandby mode Set DCS Privacy CodesTo select a DCS privacy code NOAA* All Hazards Radio ChannelsTo turn VOX mode on or off Voice Activated Transmit VOXMemory Locations To set VOX sensitivityPress the Mode button to Choose one of the followingTo recall a stored memory channel location DisplayChannel Scan To de-program a memory locationTo scan channels Press the Channel Up or Channel Down button to Press the Mode button to proceed to set privacyPrivacy Code Scan Memory Location Scan To scan memory locationsTo change call settings VibrAlert and Call AlertMode Functions General Specifications Call ToneSettingsKeystroke Tones Roger Beep ConfirmationToneGeneral Specifications FCC License General SpecificationsProduct Service Product Service Questions