Cobra Electronics PR 945 Selecting a Channel, Battery Low, Auto Battery Save

Page 3

O P E R AT I O N

ENGLISH

ENGLISH

O P E R AT I O N

Belt Clip

Lock Tab

Batteries

To install or replace batteries:

1.

Remove belt clip by releasing belt clip latch and sliding

 

clip down.

2.

Pull down on the Battery Latch to remove the battery

 

compartment cover.

3.

Insert four (4) AAA batteries. (Always use high quality

 

alkaline batteries.) Position batteries according to

 

polarity markings.

Selecting a Channel

Channels 1-7 are shared with FRS/GMRS. Channels 8-14 are FRS only. Channels15-22 are GMRS only. (IMPORTANT: See page 13 for FRS/GMRS frequency allocations and compatibility chart.)

CHANNEL

1. With the radio On, select any of the 22 channels by

SELECT

pushing the CHANNEL SELECT button up or down.

Button

 

(NOTE: Both radios must be tuned to the same channel to communicate.)

ON-OFF/

VOLUME

Switch

4. Replace Battery Compartment cover and belt clip.

(NOTE: Contact your local Cobra® dealer or Cobra® directly for optional charger accessories.)

Turning On Your microTALK® Radio

1.Rotate the ON-OFF/VOLUME switch clockwise to turn On the radio (and to adjust the volume). An audible tone will indicate the radio is On.

Your microTALK® is now in Standby mode, ready to receive transmissions. The radio is always in Standby mode except when the TALK, CALL, or MODE buttons are pressed.

Battery Low

Battery power is indicated by the segments appearing at the bottom of the LCD. As battery power decreases, fewer segments will be visible. When bA Lo begins to flash, the batteries should be replaced. If you are using rechargeable batteries, they should be recharged.

Auto Battery Save

Your microTALK® radio has a unique circuit designed to extend battery life. If there are no transmissions within ten

(10)seconds, the radio will automatically switch to Battery Save mode and POWER SAVER will appear in the display. This will not affect the radio’s ability to receive incoming transmissions.

MODE

Button

CHANNEL

SELECT

Button

Selecting a CTCSS Privacy Code

CTCSS (Continuous Tone Coded Squelch System) is an advanced tone coding system allowing you to select one of 38 privacy codes to reduce interference from other users on the channel.

(NOTE: If you are using a privacy code, both radios must be tuned to the same channel and privacy code to communicate. Each channel will remember the last privacy code you selected.)

To select a privacy code:

1.After selecting a main channel, press and release the MODE button. A small number will flash next to the channel in the LCD.

2.Push the CHANNEL SELECT button up or down to select a privacy code. You can hold the button up or down for fast advance.

3.When your desired privacy code is displayed:

a)Press the MODE button to enter the new setting and proceed to other functions.

b)Press the LOCK button to enter the new setting and return to Standby mode.

c)Do not press any buttons for 15 seconds to enter the new setting and return to STANDBY MODE.

3

4

Image 3
Contents FPO O D U C T F E AT U R E S Product FeaturesCall Button Battery Saver Circuitry Lock Button UHF FM Frequencies Backlit LCD DisplaySelecting a Ctcss Privacy Code Battery LowAuto Battery Save Selecting a ChannelListening for a Response Using the Lock FunctionCalling Another Person Talking to Another PersonProgramming Memory Locations Using the Mode ButtonUsing the Scan Function Recalling Memory LocationsTo scan memory locations Roger Beep Confirmation ToneTo scan privacy codes To turn Roger Beep On or OffKeystroke Tones High/Low PowerCall Tone Settings Signal Strength MeterNormal Position Safety Information for microTALK RadiosE C I F I C AT I O N S C I N F O R M AT I O NOrdering From U.S AccessoriesS T O M E R a S S I S TA N C E WA R R a N T Y D E R F O R MBotón de Bloqueo Frecuencias UHF FMAviso Sonoro DE Botón de LlamadaBatería con carga baja BateríasEncendido del radio microTALK Selección del canalIluminación de la pantalla Para llamar a otra personaPara hablar con otra persona Para escuchar a la otra personaPara utilizar el botón de Modalidad Programación de localidades de memoriaDe una localidad de memoria Para rastrear los canales principales Función de rastreoUso de datos en localidades de memoria Para rastrear los códigos de comunicación privadaPara encender y apagar el aviso sonoro de cambio Aviso sonoro de cambioPara rastrear las localidades de memoria Oprima el botón de Modalidad para pasar a otras funcionesDiez señales de aviso de llamada Sonido de teclasPotencia alta y baja Medidor de intensidad de señalC E N C I a S P E C I F I C a C I O N E S EspañolPara efectuar pedidos vía Internet Formularios DE Pedidos Y AccesoriosPedidos en los EE.UU Para pedidos con tarjeta de créditoImpreso en China Núm. de catálogo 480-056-P CB radios